
$140.88
See if it's really the one
Search with this product to compare it, find similar styles, or turn up something better before deciding.
Fits 02-06 RSX and 00-10 Civic including K20Z3 Si Low compliance synthetic elastomer for sharper steering Press-in install, front alignment required 3 year / 60,000 km warranty per manufacturer KCA547, front LCA offset bushings Fits 02-06 RSX, 00-10 Civic Synthetic elastomer material Requires front alignment post-install 3-year / 60,000 km warranty Description Vehicle Fitment Technical Data Install Guide Whiteline Front Lower Control Arm Offset Bushing Kit for RSX and Civic - Part #KCA547 The DC5 RSX and 8th gen Civic Si both run out of positive caster once you lower them, and that is why the steering goes light and the car wants to wander on the highway. This Whiteline front lower control arm inner bushing kit for the 2002-2006 RSX and 2000-2010 Civic replaces the soft factory bushings with offset synthetic elastomer ones that push the arm forward, adding static caster and tightening up the front end at the same time. What It Is and Why It Works Caster is what makes a car track straight and load the outside front tire properly as you turn in. Honda gives the RSX and Civic a modest amount from the factory and there is no adjustment built in. Whiteline's offset bushing moves the inner pivot of the lower arm, which tips the strut back a fraction and adds caster you cannot get on an alignment rack. The bushing itself is a low-compliance synthetic elastomer, so the arm also stops flexing under braking and cornering loads, which is where the sharper steering feel and the more consistent alignment come from. On a K20A2 Type-S on coilovers, the difference is a heavier, more connected steering feel and noticeably better stability at speed. On an FA5 Si it is the same story. This is a kit for both sides; it does not include the arms. Specs Spec Detail Part number KCA547 Type Offset caster bushing kit, front lower control arm inner Position Front, both sides Material Synthetic elastomer, per manufacturer Kit contents Bushings, tubes and grease for both arms, per manufacturer Alignment Front alignment required after install Warranty 3 year / 60,000 km on KCA-series alignment parts, per manufacturer Fitment Year Make Model Trim Engine 2002-2006 Acura RSX Base and Type-S K20A3, K20A2, K20Z1 2001-2005 Honda Civic All trims (EP, EM, ES) D17, K20A3, L13 2006-2010 Honda Civic All trims including Si (FA, FG) R18, K20Z3, LDA Whiteline and its dealers list KCA547 for the 2002-2006 RSX and the 2000-2010 Civic, which covers both the 7th gen EP and ES chassis and the 8th gen FA and FG including the K20Z3 Si. Note that we also list Whiteline KCA479 for the 2001-2006 Civic and RSX; that kit is the double-offset front-and-rear bushing set, while KCA547 is the lower inner offset kit. If you are unsure which one your car needs, call us before ordering. What to Know Before You Buy Press work is required. The factory bushings are bonded into the aluminum lower arm on the RSX and into the stamped arm on the 8th gen, and both need a proper press and the right size drivers. Budget a couple of hours per side if you are doing it yourself, or pull the arms and let a shop press them. Do not try to burn the old bushings out of an aluminum arm. Offset bushings only work if you install them clocked the right way. Whiteline's instructions show the orientation; if you get one side backwards you will pull caster out instead of adding it and the car will pull. Check both arms before torquing. Expect a firmer ride at the front and a little more road noise than the factory rubber. Grease everything in the packet on assembly. Get a front alignment afterward, this kit changes caster and camber enough that the toe will be off. If your ball joints have play, replace them while the arms are out, and if you are also chasing bump steer on a lowered RSX look at the Whiteline KCA520 roll center kit as the next step. Fitment Year Make Model Trim Engine 1996-2000 Honda Civic CX, DX, LX, EX, HX, GX (EJ, EK) D16Y, D16Z, B16A2 1999-2000 Honda Civic Si (EM1) B16A2 1997-2001 Honda CR-V All (RD1-RD3) B20B, B20Z Whiteline lists this kit for the 6th gen Civic EJ, EK and EM chassis and the RD1-RD3 CR-V. It is the inner FRONT bushing on the lower control arm only; the inner rear bushing on the same arm is a different Whiteline part (KCA366, which is the offset caster version). The 93-97 del Sol shares the EG-generation arm and is not on Whiteline's list, so we have left it off the fitment table until confirmed. Specs Spec Detail Part number W53608 Kit contents 4 bushings, 2 crush tubes, grease Bushing type Shackle style, 2 halves per side Bushing OD 37.2mm Bushing ID 22.2mm Bushing length 25.5mm each half, 7.2mm flange Crush tube 22.2mm OD x 14.3mm ID x 50mm Position Front lower control arm, inner front pivot Install time 2.5 hours, press required, per manufacturer Alignment Front alignment required after install Warranty Limited lifetime, per manufacturer
Have a question about this?
We currently ship within the US, with more countries coming soon.
Final cost and dates are confirmed at checkout.
🇺🇸 Ship from USA · On Agora since 2025
$140.88