No-Drill Vinyl Siding Mount for Ring Video Doorbell Wired (2021) | Battery & Wired Capable

Vinyl Siding Doorbell Mount for the Ring Video Doorbell Wired (2021) — Adjustable 3–5" Lap, No Screws ✔ Made in USA✔ No Drilling into Siding✔ Battery & Wired Capable✔ Free Shipping Over $100✔ Siding Fit Guarantee This no-drill vinyl siding mount holds your Ring Video Doorbell Wired (2021) on standard or Dutch lap siding without damaging a panel. It slides under the lap and locks with set screws plus extreme outdoor tape on the bottom slider. Made in the USA and 3D-printed to order from UV-stable PETG (not brittle PLA), freeze-tolerant. Ships in 2-3 business days, free shipping on orders over $100, backed by our Siding Fit Guarantee. Don’t have the doorbell yet? Buy the Ring Wired (2021) on Amazon → Compatibility — Ring Wired (2021) & Vinyl Siding This listing is set up for the Ring Video Doorbell Wired (2021) (the default selection) and also fits these similar generations — just pick yours from the dropdown: Ring Video Doorbell Wired (2021) (default) — Buy on Amazon → Ring Wired Doorbell (2nd Gen, 2026, Retinal 2K) — Buy on Amazon → Siding type: standard & Dutch lap vinyl with a 3"–5" exposed lap (taller boards via Vinyl Board Length). Battery & wired capable: wire access holes let you charge/hardwire a battery model or power a wired one. Power: Wired — route existing 16-24V wires through the wire access hole. No wires at that spot? Use a 24V AC power adapter with wire clips → Not sure which you have? See our Ring Model Guide, or send a photo. Need the doorbell? Shop the Ring Wired (2021) on Amazon → How the No-Drill Install Works The top clip rotates and slides under the bottom edge of the upper siding panel. The bottom bracket slides up to grip the lower lip of the target panel. Adjusts to fit siding laps between 3" and 5" (taller boards via the Vinyl Board Length option). Set screws lock the adjustable pieces once fitted to your siding width. Included extreme outdoor tape goes on the bottom slider (the piece that grips the lower siding lip) for extra hold. Wire access holes let you route a charging or low-voltage power cable for battery OR wired doorbells. The adapter plate is pre-drilled for the exact generation you select from the dropdown. No special tools, no drilling, no holes in your siding. Vinyl Siding Mount — Specs Mounts on: standard & Dutch lap vinyl siding, 3"–5" exposed lap (standard); 5.5–7.5" and 7–8.5" via Vinyl Board Length Install: no-drill / screwless — clips under the siding lip, locked with set screws + extreme outdoor tape on the bottom slider Adapter Plate: pre-drilled to match the Ring generation you select in the dropdown Wire Access Holes: route a charging or low-voltage power cable — battery or wired (use a 24V AC power adapter where there are no existing wires) What’s Included: adjustable vinyl siding adapter bracket + set screws + extreme outdoor tape (for the bottom slider) + doorbell mounting screws Material: UV-stable PETG, 3D-printed in the USA, freeze-tolerant Color: Black standard (White available) Price: $32.50 (3–5" lap) · $35.00 (5.5–7.5") · $37.00 (7–8.5") Key Features & Benefits No Drilling into Siding: Installs securely without a single screw into your vinyl panels. Custom-Fit Adapter Plate: Pre-drilled to match the Ring Wired (2021) — no rattles, no gaps. Battery & Wired Capable: Wire access holes route a charging cable or low-voltage power — pair with a 24V AC adapter where there are no wires. Adjustable Siding Fit: Works on most vinyl siding with 3"–5" lap; taller boards via the Board Length option. Stays Put: Locking set screws plus extreme outdoor tape on the bottom slider keep it firmly in place. UV-Stable PETG: 3D-printed in the USA, freeze-tolerant. Common Applications This no-drill vinyl siding mount for the Ring Wired (2021) series is a great fit for: Dutch lap and standard lap siding from 3" up to 8.5" boards relocating the camera to get a better view of the porch, steps, or driveway second-camera spots on the garage or side wall, all on vinyl siding Customization & Add-Ons Color Change: Default Black; White and other siding-matching colors — Color Change Request → Extreme Outdoor Tape Add-On: Extra-strong tape for the bottom slider on very smooth or textured siding — Add Extreme Outdoor Tape ($2.50) → 24V AC Power Adapter: Power your wired doorbell where there are no existing wires — 24V AC power adapter with wire clips → (Pick your exact generation and siding board height from the options above.) Helpful Guides & Resources Tips for Vinyl Siding Camera Mounts Smart Ways to Mount Doorbells in Apartments DoorbellMount.com FAQ & install help Manufacturer info: Ring official site Installing Your No-Drill Vinyl Siding Mount Select your generation & board length so the plate is pre-drilled correctly and the bracket matches your siding lap. Loosen the set screws and open the bracket to roughly your siding lap width. Hook the top clip under the bottom edge of the upper siding panel. Slide the bottom bracket up until it grips the lower lip of the target panel snugly. Tighten the set screws to lock the fit, then apply the included extreme outdoor tape to the bottom slider for extra hold. Attach the doorbell to the pre-drilled adapter plate using the screws provided with this mount. Route any power/charging cable through the wire access hole (a 24V AC adapter works where there are no wires). Confirm the view in the Ring app and adjust the bracket position along the siding if needed. Tools: small flathead/Phillips for the set screws and doorbell screws. No drill required. FAQ — No-Drill Vinyl Siding Mount for the Ring Wired (2021) Will it fit my vinyl siding?It fits most standard and Dutch lap vinyl siding with a 3"-5" exposed lap (~95% of homes). For taller boards, choose the 5.5-7.5" or 7-8.5" Vinyl Board Length option. Send a photo if unsure. Does it damage or put holes in my siding?No. The bracket clips under the siding lip and locks with set screws plus extreme outdoor tape on the bottom slider - no drilling and no screws into the panels. Which generation do I pick?This listing is set up for the Ring Video Doorbell Wired (2021) and also fits Ring Wired 2nd Gen. Pick your exact generation from the dropdown and we ship the matching pre-drilled plate. How do I power a wired doorbell on vinyl siding?Route your existing 16-24V wires through the wire access hole. No wiring at that spot? Use a 24V AC power adapter with wire clips (linked on this page). Is it weatherproof?Yes - UV-stable PETG (not brittle PLA), freeze-tolerant across normal North American climates. What color is it?Black is standard; White is available. For siding-matching colors, use the Color Change Request. Can I use this on a rental?Yes - it clips under the siding with no drilling and no holes, and removes cleanly if you move. ✔ Siding Fit Guarantee — Guaranteed to Fit Your Siding We’re confident this fits vinyl siding with a 3"–5" exposure. If you hit a fit issue, we’ll make it right at NO additional cost. Before you order: Send a photo of your siding and doorbell — we’ll confirm the right generation and board length. If it doesn’t fit: Send pictures and we’ll provide free replacement parts until you get a perfect fit. Reach us: 833-326-6868 / shop@doorbellmount.com. Covers fitment only — not parts damaged during or after install. Need the Doorbell, Power, or Extra Supplies? Ring Video Doorbell Wired (2021) on Amazon Ring Wired Doorbell (2nd Gen, 2026, Retinal 2K) on Amazon 24V AC Power Adapter with wire clips on Amazon — power a wired doorbell or charge/hardwire a battery model Extreme outdoor mounting tape on Amazon — or add our Extreme Outdoor Tape add-on ($2.50) Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases at no extra cost to you. These small commissions help fund development of new mounts and brackets. Questions About Siding Type, Model, or Install? Send pictures of your siding and doorbell — we’ll confirm before you order: Email: shop@doorbellmount.com Text/Call: 1-833-326-6868 Standard Color: Black (White available). For siding-matching prints, use the Color Change Request. Shop all mounts at DoorbellMount.com. 3D-Printed Parts Note: Each mount is 3D-printed to order in UV-stable PETG. Minor layer lines are normal and do not affect strength or fit. Black is standard; custom colors via the Color Change Request. Order your No-Drill Vinyl Siding Mount for the Ring Wired (2021) today — screwless install, no holes, battery & wired capable, free shipping over $100, Siding Fit Guarantee. Select your generation and board length.