TPO Flooring - Coin

State-of-the-art technology advanced TPO (thermoplastic polyolefin) flooring membrane Versatile enough to meet almost any interior or exterior application requiring resistance to weather, chemicals and traffic. Black or Gray nickel plate design Stocked in 97" wide roll and sold per linear foot (97" x 12") individual Or purchase in pre-cut lengths per van size (see below). Sheets come slightly oversized so you can trim wheel wells and overall length to correct sizing. Save 10% on TPO Coin Adhesive (#61511) when added to your flooring order. *Not Valid with any other discounts* Sold by Linear Foot  97" wide x 12" long (just add qty to cart) Sprinter 144 72" wide x 146" long (13ft) Sprinter 170 72" wide x 182" long (16ft) Sprinter 170 EX 72" wide x 194" long  (17ft)   What's So Amazing? Décor TPO is highly chemical resistant to gasoline, diesel fuel, antifreeze, battery acid, engine oil, transmission fluid, brake fluid, cleansers and many other common chemicals. It meets all safety regulation criteria for Federal Motor Vehicle Safety Standard (FMVSS) #302 Certification. Unlike competitive vinyl (PVC) membrane products, the TPO will not emit toxic fumes when burnt. Décor TPO has excellent weathering characteristics, durability and mechanical performance with inherent UV stability and skid resistance. This makes it a tremendous high traffic and extreme exposure membrane. It does not emit any notable odor commonly experienced with competitive rubber-based membranes. TPO flooring incorporates a spun polyester (fleece) backing, which is mechanically attached during the extrusion manufacturing process. This backing enables TPO flooring to be easily bonded to a variety of porous wood surfaces. Alpha Systems 3080 TPO Flooring Adhesive is recommended for bonding TPO flooring.     Installation Instructions: Alpha Systems 3080 TPO Flooring Adhesive may be applied with brush, roller or trowel. Surface should be free of dirt, oil, or other contaminants. Apply a coat of adhesive to one surface (16-20 mils thick). Mate the two surfaces as soon as possible (approx. open time 5-10 minutes. Use a 70 lb. linoleum roller (or equivalent) to apply pressure so that adhesive can properly penetrate into the fleece. IMMEDIATELY following the adhesive application and rolling process mechanically fasten the perimeter of the TPO flooring.     Technical DICOR TPO MEMBRANE MATERIAL PRODUCT PROPERTIES Property Attained value Test method Melt flow rate (230C – 2.16kg) 1.5 – 3.0 g/10 min. ASTM D1238 Specific gravity 0.93 ASTM D792 Tensile strength (2”/min) 1933 psi (14 MPa) ASTM D638 Flexural modulus 17,600 psi (121 MPa) ASTM D790 Elongation at break (2”/min) 586% ASTM D638 Notched izod impact No break ASTM D256 Gardner impact (-30C) 240 lbs. ASTM D5420 Low temperature flexibility No cracking ESB-M5G52A Hardness 98 shore A ASTM D2240 Coefficient of linear thermal expansion 2.8x10-5 in/in/ºF ASTM D696 % CLTE movement @ 110ºF temp change* 0.31% (31/100’s of 1%) Calculated *Represents a temperature change of 70ºF to 180ºF or 70ºF to -40ºF DICOR TPO COEFFICIENT OF FRICTION Surface Texture Diamond plate Levant texture Test conditions Static Kinetic Static Kinetic Dry 0.76 0.75 1.57 1.55 Salt Water 0.98 0.97 1.63 1.61 Fresh Water 0.99 0.97 1.40 1.38   NOTE: The Coefficient of Friction was performed in accordance with ASTM D1894-01 procedures. Specimens were tested against 1/8” thick Neoprene block with Durometer Hardness 70 Shore A (replicates common tennis shoe). The 422-CR were tested in 3 conditions: dry, wet and salt water and wet and fresh water. DICOR TPO FLAMMABILITY Décor TPO meets all safety regulation criteria for Federal Motor Vehicle Safety Standards (FMVSS) #302 Certification.     Roll Size: 102" Application: Décor floor adhesive Patterns: Nickel Plate Color: Standard: Black. Other colors are available through special order. Width (Inches) 102.000 Height (Inches) No Depth (Inches) No