Tech21 RK5-V3 Richie Kotzen Signature Fly Rig v3

The Richie Kotzen RK5 Signature Fly Rig was developed in close collaboration with Richie, whose input was invaluable. Meticulous about every facet of his playing, singing, songwriting and tone, Richie’s attention to the details of his Signature Fly Rigs is nothing less. Since the debut of the original RK5 in 2014, Richie’s needs have changed, both on and off the road. The RK5 v3 retains the same SansAmp section, Reverb/Delay/Roto section, and Richie’s Signature OMG overdrive. New features include a switchable Pre/Post Boost to beef up drive and distortion or increase the overall volume to punch up fills and solos, along with the addition of an Effect Loop. Additionally, the RK5 v3 is pre-configured to provide phantom power for his Tech 21 Signature RK Killer Wail wah. (For more info, click HERE.) Richie is actively involved and responsive in the entire design process. Having both a working and personal relationship with Richie, is a tremendous highlight in our history. More PRE/POST BOOST Switchable Pre/Post Boost up to 20dB to beef up drive and distortion or increase the overall volume to punch up fills and solos. OMG OVERDRIVE + FUZZ OMG is based upon the Richie Kotzen Signature OMG pedal, which provides a wide range of overdrive, from clean to aggressive. You can add personality to a clean amp or use it for extra punch with a dirty amp tone. Controls include Drive for the overall amount of gain and overdrive, and Tone with specialized voicing for adjusting the high-end and mid-range. FUZZ Switch changes the character and attack of the overdrive to a fuzz-style tone, making it thicker and woolier. SANSAMP The SansAmp section of the RK5 includes 3-band active EQ, and Level and Drive controls. It focuses on clean tones within the tube amplifier sound spectrum. To dirty things up, you have the flexibility of using the Drive control, the Boost function, or you can add overdrive from the OMG section. Or all three. Each method achieves different tones. The all-analog SansAmp technology enables the RK5 to run directly into mixers of recording desks and PA systems, as well as augment your existing amplifier set-up. It can also be used to record directly and enhance previously recorded tracks. BUILT-IN SPEAKER/CAB SIM The 100% analog SansAmp Tube Amplifier Emulation technology encompasses the entire signal chain, from pre-amp to power amp to speaker simulation. An integral part of the circuitry, the SansAmp speaker simulation will complement any type of guitar or bass speaker cabinet system. You can also place an external IR after a SansAmp to give additional flavor if you so desire. The SansAmp speaker sim is designed and individually tailored for a smooth, even response as would be achieved by a multiply-miked cabinet –without peaks, valleys, and notches associated with single miking and many IRs. REVERB + TUNER Independent footswitchable reverb features a single, continuously-variable control. It provides a smooth, full sweep to easily dial-in the amount of reverb desired. Choose between large and small “room sizes.” Chromatic Tuner is operable via the REVERB/TUNER footswitch. You simply hold the footswitch down to engage the Tuner, which simultaneously mutes the signal path. DELAY + ROTO WITH TAP TEMPO DELAY is voiced for the sounds of a vintage tape echo. It features Time and Repeats controls and dedicated Tap Tempo footswitch. There’s also a Drift control which adds a random, unpredictable element to the modulation in keeping with its vintage roots. ROTO changes the Delay function into a rotating speaker effect. Tap Tempo then controls the speed. Just like the real thing, it will ramp up from slow to fast to gradually reach a new speed. Drift then controls the distance of the virtual mic to the rotating speaker. At maximum, it adds a tremolo-like effect by modulating the volume in sync with the tonal modulation. Specs 1/4-inch 1megOhm input XLR output with ground lift 1/4-inch low impedance output Post SansAmp, pre-effects Effect Loop Rugged, all-metal housing Metal footswitches and jacks Silent-switching, custom footswitch actuators Measures 12.5”l x 2.5”w x 1.25”h Weight: 20.7 oz. Utilizes included 9V DC Universal Power Supply: Tech 21 Model #DC9. “Auto-switching,” self-adjusting 100V-240V, 200mA. Includes interchangeable international prong assemblies for EU, UK, Australia/New Zealand for use anywhere in the world.