StickBug WE Speed Loaders

StickBug is an airsoft gas blowback speed loader design that functions like real steel stripper clips to make on-field magazine reloading simple and ergonomic. The system is based on classic ramrod-style speed loaders with a bunch of added features to make field reloading viable as well as provide advantages over more common plunger-style speed loaders. Self-contained - no adapters, separate bits, or ramrods are required. Simply pull a StickBug out of a pouch, reload your mag, and then toss it into your dump pouch. Captive parts - parts stay together and are secured in place even after being used. BBs won't leak out even in the heaviest of maneuvers. The follower is captive while loaded and unloaded so you have peace of mind the BBs will be there when you need it and your StickBug stays together for the next round. Compact and light - 15 grams unloaded with the footprint of a chem light, StickBug gives you flexibility where you store extra ammo on your gear. No need to dedicate your general-purpose pouch to the speed loader. Keep your heavy mags in the fight and fill your dump pouch with these instead to avoid weighing yourself down. Silent - captive BBs and tight tolerances mean no rattle! Move silently around the field without the loud rattle of a standard plunger speed loader giving away your position. Consistent loading - load the same amount of BBs, evenly, and quickly. One smooth motion to load your mags with a prescribed amount of BBs saves both your mag's feed lips and prevents mag overfilling. Durable - StickBug is made of PETG and designed to withstand field conditions. You can expect 100+ uses and it will survive being dropped, stepped on, and all the fumbles that might occur during intense action. Ergonomic - tailor-made adapter end mates securely with your mag's feed lips so alignment is easy. Ramped tabs on the follower make gloved use easy as well. Loading the StickBug is easy with a chamfered loading hole and embossed fill markers.  Included Contents: 2 PACK - 2x WE StickBug 15 Round Stripper Clips (Note: 30 rounds total, 2 StickBugs per mag for full reload) 4 PACK - 4x WE StickBug 15 Round Stripper Clips (Note: 60 rounds total, 2 StickBugs per mag for full reload) Tested Compatibility: WE M4 Mags WE SCAR_H Mags WE PDW Mags WE MSK Mags Q&A: Why 15 rounds? - StickBug is intended to be versatile and part of that is fitting in normal tactical pouches. Currently, the 15-round StickBug is the length of a standard M4 mag and four of them side by side are the same width as a standard M4 mag. A 30-round StickBug would be almost twice as long and would not only fit most pouches but also be harder to keep straight during reloads. How would I load StickBug? - StickBug is intended to be loaded off the field or in less active times. Simply remove the follower, load the tube with BBs up to the 15-round mark, and snap the follower back into the top retaining catch of the tube. A standard plunger speed loader is recommended to load StickBug, but keep this in the safe zone or in a backpack to get the silence benefit. What if I lose the follower? - Things happen! We sell replacement followers as well to make sure you can keep playing with our product and not have to buy a whole new one, though we also recommend having lots of StickBugs as well. What if my mag is not listed as compatible? - Our mission is to support the community and test our product with our target platform to ensure function. If your mag is not listed but your system is compatible with that platform then we might have just not tested your kind of mag yet. You can reach out and we advise your decision. We also plan on continually adding more supported platforms and mags to the StickBug line. Do I need two StickBugs for one mag? - If your mag is 30-35 rounds we recommend having two StickBugs per mag for a full reload. This is a compromise due to form factor and ergonomics but is still quick to use in practice. We sell StickBug in even-numbered packs to support this intended use. Disclaimer - StickBug is a fully 3D printed part and therefore may arrive with minor cosmetic defects that are normal to the 3D printing process. Any minor wisps or strings missed in QC are a result of the 3D printing and are not hair. All parts are functionally QC tested before being shipped.