Stealth Lifting Shore

The Ellis Stealth Lifting Shore is an adjustable structural support system designed to be both strong and narrow.  Each Stealth Shore has a max width of 3.5" and is able to fit and be sealed inside a standard 2x4 framed wall.  The patented Ellis Thrust Bearing Nut Assembly increases lifting capacity under load by up to 10x.  These lifting jacks can be used for temporary or permeant support loads up to a 20,000 lbs.  Specifications All Ellis Stealth Lifting Shores now come with the 4 lug lifting nut. Used the 3/4" Diameter Steel Adjustment Rod to lift loads up to 20,000 lbs. The patented Ellis Thrust Bearings on the Stealth Lifting Shores enable these shores to lift up to 10x the amount of load compared to the Light Duty Steel Shores (w/o bearings).   Adjustable structural support column for temporary or permanent support with a patented nut housing tiny thrust bearings to allow for easier adjustment under load and jacking weight with significantly less force.  Add any length 3/4" Diameter Steel Adjustment Rod for extra leverage and lift up to 20,000 lbs. In the product animation below the Ellis Stealth Shore lifts a sagging header beam back into place.  The locking set screw secures the nut to the screw to prevent any further adjustment.  Then the wall is sealed with drywall.   The 3-1/2" x 3-1/2" top plate is attached with a clevis pin and interchangeable with different shapes and sizes. Click here to see a few of the different tops to choose from: STEEL SHORE TOPS. *All Load Capacities include a 2.5 to 1 Factor of Safety. Demonstration Video Specifications Nut Assembly - Forged for durability, galvanized. Houses tiny thrust bearings to allow for much easier adjustment under load. Lockable with safety lock set screw (included) for permanent use. Top plate - 1/4" x 3-1/2" x 3-1/2" Steel Plate, 4 - 1/4" holes spaced 1/2" OC (Attaches with clevis pin and Interchangeable with custom U Heads.) See below for more adjustable top plate options. Base Plate - 1/4" x 3-1/2" x 3-1/2", 4 - 1/4" Holes spaced 1/2" OC (welded to 2" Sched. 40 Pipe). Custom sizes available Acme Screw - 1-7/8" Dia. (Lengths vary). Pipe - 2" Sced. 40 (Lengths vary). Interchangeable Top Plate Options: Flat Plate - Standard with any Light Duty Steel Shore Lumber U-Head - Compatible with Light Duty Steel Shores and is intended to be used to secure to a horizontal 2x4, 2x6, 4x4, 4x8, 6x6 etc. lumber beam. Pivot Flat Plate  - This 6" square plate is intended to secure your Light Duty Steel Shore to a beam being supported and will pivot up to 45 degrees.  This product fits on Light Duty Steel Shores only. Custom Top Plate shapes and sizes specific to Light Duty Steel Shores upon request (800) 654-8311 or store@ellismanufacturing.com. *STEALTH-3, STEALTH-4, STEALTH-5 do NOT have interchangeable tops.  Tops are welded directly onto the screw and can not be removed. Shop Drawings: Item Number Shop Drawing (.PDF) STEALTH-3 STEALTH-3 Shop Drawing STEALTH-4 STEALTH-4 Shop Drawing STEALTH-5 STEALTH-5 Shop Drawing STEALTH-8 STEALTH-8 Shop Drawing STEALTH-10 STEALTH-10 Shop Drawing STEALTH-14 STEALTH-14 Shop Drawing STEALTH-22 STEALTH-22 Shop Drawing STEALTH-38 STEALTH-38 Shop Drawing STEALTH-62 STEALTH-62 Shop Drawing STEALTH-86 STEALTH-86 Shop Drawing STEALTH-110 STEALTH-110 Shop Drawing *Steel Shores should be attached to a flat solid foundation. Steel Shores should not be subject to any lateral force. Steel Shore should be used to support straight vertical loads only. We recommend tightening set screw in the side of the nut with 6mm allen wrench prior to loading.  Do not extend screw past advertised adjustment range.  Do not exceed max safe load capacity.  Before construction begins it is recommended that you consult with a certified engineer for approval of our products within your application.