RTD Data Acquisition 8-Layer Stackable HAT for Raspberry Pi

FEATURES NEW: V7 supports PT100 and PT1000 sensors NEW: Sensor selection in software. No jumpers! NEW: 5A current transfer for Raspberry Pi 5 24 bit delta-sigma A/D converters Factory accuracy: 0.1% Maximum accuracy (through calibration): 0.01% Maximum acquisition speed 40 cps Eight layer stackable to 64 RTD channels RS485/MODBUS transceiver PT100 sensors, -200°C to 765°C range PT1000 sensors, -50°C to 500°C range Programmable threshold LEDs on all inputs Pluggable Connectors 26-16 AWG wires On-board hardware watchdog able to power cycle the Raspberry Pi 5V power supply provides power to Raspberry Pi General Purpose Pushbutton On-board resettable fuse RTD DAQ Raspberry Pi Uses only I2C port, all GPIO pins available Works with any Raspberry Pi from ZERO to 5 ECCN Code EAR99 Command line  Python library Node-Red nodes Modbus RTU CODESYS Driver OpenPLC module Arduino Library Home Assistant Integration The Revision 6.x of the RTD card has an RS485 transceiver, works with PT100 sensors, and has programmable LEDs indicating the status of all inputs.  DESCRIPTION Compatible with all Raspberry Pi versions from Zero to 5, the RTD Data Acquisition Card offers a compact and inexpensive solution  for reading and storing data from up to 64 PT100 temperature sensors. Using 24 bit delta-sigma A/D converters with four channels each, the card achieves better than 0.1% accuracy. Field calibration with a precision 100Ω resistor can lead to 0.01% precision. Since temperature measurement using RTD is based on resistance, the resistance in the lead wires and connectors must be taken  into account when calculating the overall resistance in the system circuit.  Using a 3-wire circuit design allows lead wire resistance to be factored out of the overall calculation.  COMPATIBILITY The card is compatible with all Raspberry Pi versions from Zero to 5. It shares the I2C bus using only two of the Raspberry Pi’s GPIO pins to manage all eight cards.  This feature leaves the remaining 24 GPIOs available for the user.  POWER REQUIREMENTS The card needs 5V to operate and can be powered from Raspberry Pi or from it's own pluggable connector. The cards needs 50mA to operate. STACKING MULTIPLE CARDS Up to eight RTD Data Acquisition cards can be stacked on your Raspberry Pi. Three positions of the configuration DIP Switch labeled ID0, ID1, ID2 are used to select the stack level. Cards can be stacked in any order. BOARD LAYOUT ELECTRICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS SOFTWARE SOFTWARE INTERFACES You can write your own Data Acquisition system in C, C++, PERL or the language of your choice using the Command Line functions or the Python Library. A browser interface can easily be deployed using Node-Red.  FIELD CALIBRATION Field calibration to 0.01% precision can be achieved using an external high precision resistor. Software commands permit the user to calibrate the card in two points (the 2 points must be as far as possible but inside the measurement range). The resulting values are stored in flash and used for resistance measurements compensation witch will reflect in the temperature readings. The resistance to temperature conversion is made by the simplest equation T = (R - R0)/(R0*k), where T is temperature in Celsius degree; R is the sensor resistance; R0 is the resistance at 0 deg Celsius (100 for PT100, 1000 for PT100) and k= 0.00385. If the user need to use the polynomial equation, the resistance measurements are available.  RS485/MODBUS Communication The RTD Data Acquisition card contains a standard RS485 transceiver which can be accessed by the local processor or by Raspberry Pi. The desired configuration is set from two bypass jumpers on the configuration connector J3. See in the CARD LAYOUT jumpers "485-RX" and "485-TX". If jumpers are installed, Raspberry Pi can communicate with any device with an RS485 interface. In this configuration the card is a passive bridge which implements only the hardware levels required by the RS485 protocol. To use this configuration, you need to tell the local processor to release control of the RS485 bus: ~$ rtd

rs485wr 0 0 0 0 0 If jumpers are removed, the card operates as MODBUS slave and implements the MODBUS RTU protocol. Any MODBUS master can access all the card's inputs, and set all the outputs using standard MODBUS commands. A detailed list of commands implemented and parameters addresses can be found on GitHub: In both configurations the local processor needs to be programmed to release (jumpers installed) or control (jumpers removed) the RS485 signals. See the command line online help for further information. LED threshold signals The RTD Data Acquisition card has eight LEDs that can be activated when the input reaches a preset threshold. The threshold can be set in software for each input.  FIRMWARE UPDATE The card firmware can be updated in the field by running a command. The update is made with the latest firmware version located on our servers. More instructions about the process can be found on GitHub. Please make sure there is no process, like Node-Red or python scripts, that tries to access the card during the update process. DOWNLOADS RTD DATA ACQUISITION DOWNLOADS ACCESSORIES DIN-RAIL MOUNTING The RTD Data Acquisition card can be installed parallel on a DIN-Rail using the DIN-Rail Kit Type 1, or perpendicular using the DIN-Rail Kit Type 2. YOUR KIT 1. 8-Channel RTD HAT for Raspberry Pi 2. Mounting hardware Four M2.5x18mm male-female brass standoffs Four M2.5x5mm brass screws Four M2.5 brass nuts 4. All female connector plugs QUICK START Plug your card on top of your Raspberry Pi and power up the system Enable I2C communication on Raspberry Pi using raspi-config. Install the software from github.com: ~$ git clone https://github.com/SequentMicrosystems/rtd-rpi.git ~$ cd /home/pi/rtd-rpi ~/rtd-rpi$ sudo make install ~/rtd-rpi$ rtd The program will respond with a list of available commands.