RD600.1

What's in the box: Amplifier Metal Bass Remote with Clip Indicator Owner's Manual Mounting Screws Warranty Description: What is special about the RD Series: More watts per dollar! We are delivering more true RMS watts per dollar spent then our competitors. Especially considering that this amp was properly engineered in the USA. Compact! The RD series by Rockville is a compact class “D” amp that will not take up a lot of your valuable trunk space. Engineered in the USA This amp delivers clean power to your subs. We benchmarked this against some of the top selling amps on the market and here are some differences making our amp better: Our amp has some of the best efficiency numbers on the market which means our amp will not strain your battery as much as some less efficient ones Our bass boost is properly engineered to boost the 45Hz frequency. Many amps we benchmarked this against have a bass boost that boosts 80Hz which makes it counter-productive. We pay a lot of attention to detail during our engineering phase in order to deliver a top-notch product at a great price. Metal Bass Remote with Clipping Indicator We include a high quality metal bass remote with a clipping indicator that allows you to easily increase your bass to its max level before distortion in real time. (This changes from song to song depending on the crest factor of your song). Some of the competing amps do not even have a clipping indicator on the actual amp which can cause you to blow your subs. Tiffany RCA cables We use tiffany style RCA terminals which are known to be the most secure and reliable on the market. This Amp Can Handle the Heat! Our amp will not easily go into thermal protection. It dissipates heat efficiently. We tested it on an audio precision at 4 ohms with full power at 100 Hz for 45 minutes and the amp stayed cool and did not go into protect. Most amps on the market would go into protect in around 30 minutes if it’s a good quality amp. This is a true class “D” design. Be careful with half-bridge designs. They are cheap to produce, but the sound quality, longevity, and safety of them are questionable. Features: Rockville RD600.1 600 Watt Dyno-Certified RMS (2400w Peak) Mono 1 Ohm Car Amplifier Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc) 1 Ohm: 600 Watts x 1 Channel <1% THD+N (75% efficient) 2 Ohm: 400 Watts x 1 Channel <1% THD+N (85% efficient) 4 Ohm: 250 Watts x 1 Channel <1% THD+N (90% efficient) Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc) 1 Ohm: 2400 Watts x 1 Channel 2 Ohm: 1600 Watts x 1 Channel 4 Ohm: 1000 Watts x 1 Channel Power/Protect/Clip LED Indicators on the front panel High-Speed MOSFET Power Supply High Performance Class D Technology Bass Boost @45Hz: 0dB-12dB Low Pass Filter: 50Hz - 200Hz Subsonic Filter: 10Hz - 50Hz Full IC-Controlled Protection Circuitry Remote Subwoofer Control Mute and Delay Soft Start System RCA Line Output (Tiffany style terminals) 8 Volt Preamp Circuitry Status Mode LED Indicator Minimum THD at Rated Power: <0.5% A Weighted Signal to Noise (per CEA 2006 Standard): -91.9dBA Frequency Response: 10Hz - 200Hz Damping Factor: >150 @ 100Hz Remote Level Attenuation: 0 to -26dB Useable Input Signal Voltage Range into 4 ohm load: 264mV – 8.0V Actual Maximum THD+N at 4 Ohm rated power: 0.5% Battery voltage limits for amplifier operation: 8v to 16.1v 2 x 30 Amp Maxi Fuse (Built in) 4 Gauge Power and Ground Terminals 8 Gauge speaker wire terminals Dimensions: (W x H x L) 9.6” x 4.9” x 1.8"