Proline X Micro Series Dual 10" Sealed Enclosure - Fits Wavtech thinPRO 10

Micro Series | Dual thinPRO 10 | Enclosure Only Dual 10". 4.5 Inches Deep. 0.40 cu ft Per Chamber — Wavtech's Optimum. Two Wavtech thinPRO 10 drivers. Two isolated sealed chambers. Each chamber holds 0.40 cubic feet of net airspace — which after driver displacement accounts for exactly Wavtech's 0.35 cubic foot sweet spot. The M10D-S WAV delivers dual 10" output from a 44-inch wide, 4.5-inch deep footprint designed for full-width behind-seat truck installs and wide cargo floor applications where a conventional dual 10" build would never fit. 0.80 Cu Ft Net Total 0.40 Cu Ft Per Chamber 4.5" Total Depth 1,500W Combined RMS Rating Enclosure only. Wavtech thinPRO 10 subwoofers are not included and must be purchased separately. This enclosure accepts both the thinPRO10-2 (Single 2Ω) and thinPRO10-4 (Single 4Ω). Final load depends on which variant you choose and how they are wired. 0.40 cu ft Per Chamber — Net After Displacement, Optimum Acoustic Airspace Wavtech publishes a sealed sweet spot of 0.35 cubic feet for the thinPRO 10, with an acceptable range of 0.25–0.80 cubic feet. The M10D-S WAV delivers 0.40 cubic feet of net volume per chamber. That figure already accounts for driver displacement — each thinPRO 10 sees 0.35 cubic feet of net acoustic airspace after its own displacement is subtracted from the 0.40 cubic foot chamber. This puts each driver precisely at Wavtech's published optimum, not approximately near it. Running two drivers in a shared enclosure is not a matter of doubling a single-driver box. Each driver needs its own acoustically isolated chamber to load correctly. The M10D-S WAV uses a dual-chamber construction with a CNC-cut, dado-jointed chamber divider. Neither driver shares airspace with the other. Each chamber independently delivers the correct volume for the thinPRO 10's T/S parameters. Extra-Wide, Minimal Depth — Stack-Fab Built to Stay Inert at 4.5" At 44 inches wide and 4.5 inches deep, the M10D-S WAV is the widest, shallowest enclosure in the Micro Series. The extra-wide format is intentional — it spans the full width of most full-size truck cab floors, placing both drivers at opposite ends of the available space for maximum acoustic separation and even bass distribution across the cabin. The front baffle is a double-layer stack-fab build — two CNC-cut Langboard Elite MDF panels bonded to 1.5 inches total. At 4.5 inches of total depth, panel width is the primary geometric rigidity constraint. Stack-fab layering and dado joinery at every panel joint — with dowels reinforcing the assembly throughout — compensate for what shallow panel depth cannot provide alone. Both drivers mount flush to the baffle face, sealed with their gaskets against the double-layer front panel. Impedance Wiring — Know Before You Order 1Ω Two thinPRO10-2 (Single 2Ω) wired in parallel. Maximum power extraction. Requires an amplifier explicitly rated for sustained 1Ω operation. 2Ω Two thinPRO10-4 (Single 4Ω) wired in parallel. Broadest amplifier compatibility. Recommended configuration for most builds. 4Ω Two thinPRO10-2 (Single 2Ω) wired in series. Safest electrical configuration. Requires a monoblock with strong 4Ω output to hit the power ceiling these drivers need. Volume 0.40 cu ft Per Chamber — Displacement Accounted For Each chamber holds 0.40 cu ft net. After driver displacement, each thinPRO 10 sees 0.35 cu ft of acoustic airspace — Wavtech's published sweet spot. This is not approximated from external dimensions. It is calculated net volume with displacement already subtracted. Format 44" Wide — Full-Width Truck Cab Fitment At 44 inches wide, the M10D-S WAV spans the full floor width of most full-size crew cab and extended cab trucks. Both drivers sit at opposite ends of the available floor space, maximizing acoustic separation and even bass distribution across the cabin. Baffle 1.5" Double-Layer — Flush-Mounted Drivers Two bonded layers of Langboard Elite 3/4" MDF at 1.5 inches total. Both thinPRO 10 drivers mount flush to the baffle face, sealing against their gaskets against the double-layer front panel — no recessed pockets, no fitment gaps. Chambers Dual Chamber — Acoustically Isolated, CNC Divider A CNC-cut, dado-jointed chamber divider separates the two driver volumes completely. Neither driver shares airspace with the other. Each thinPRO 10 loads into its own sealed 0.40 cu ft chamber independently — correct acoustic alignment on both sides, every time. Wiring Single Proline X Terminal Cup — Pre-Wired One Proline X ABS/carbon fiber terminal cup with stainless hardware serves the entire enclosure. Pre-wired internally with 12-gauge OFC to both driver positions. Connect your single amplifier run to the terminal and both drivers are fed — clean, simple, no splicing required. Mounting 8/32 Threaded Inserts — Both Baffles Both baffle positions are fitted with 8/32 threaded inserts. Stainless machine screws are included for both drivers. Each thinPRO 10 threads into steel — not MDF. Consistent clamping force, no stripping, clean reinstallation at any future service. Configuration Front-Firing or Downfiring — Feet Included Rubber feet for downfiring installation are included. The extra-wide format lays flat across a truck cab floor in downfire orientation, coupling both drivers' output to the full floor surface. This is the most effective install configuration for this enclosure in a full-size truck cab. Reinforcement Dowel-Reinforced Stack Fab Throughout Dowels throughout the stack-fab assembly add mechanical alignment and shear resistance at panel joints beyond what dado joinery and adhesive alone provide. At 1,500 watts RMS combined across two drivers in a 4.5-inch-deep enclosure, dado + adhesive + dowels — all three systems — is the correct structural standard. Ready to Mount. Ready to Wire. Ready to Downfire. The M10D-S WAV ships fully prepped. The Proline X terminal cup is installed and pre-wired with 12-gauge OFC to both driver positions — one amplifier run, both drivers fed. Both baffles use 8/32 threaded inserts with stainless machine screws included. Rubber feet for downfiring are included. Polyfill is factory-installed in both chambers. Single Voice Coil — Single Connection Per Driver The thinPRO 10 is a single voice coil driver — no wiring configuration at the driver level. Select the 2Ω or 4Ω variant at purchase based on your target system impedance. Wire both drivers to the terminal cup in parallel or series to achieve your final amplifier load. See the impedance wiring chart above before selecting your variant. Where It Fits The M10D-S WAV's 44" wide, 4.5" deep format is purpose-built for full-width behind-seat and cargo floor installs. Measure the available width carefully — 44" is a significant span: Behind-seat floor — full-size crew cab trucks (full-width) Behind-seat floor — extended cab trucks (full-width) Flat cargo floor — full-size SUVs and vans Trunk floor — full-size sedans with wide trunk openings Downfire on cab floor — maximum floor coupling, both drivers Stealth under-seat builds — any vehicle with 44"+ floor width at 4.5" clearance 2-Year Warranty All Proline X Micro Series enclosures carry a two-year manufacturer's warranty against defects in materials and workmanship. Built and inspected in our Tullahoma, Tennessee facility before shipment. Contact Audio Intensity directly for warranty support. Made in Tennessee Every Proline X Micro Series enclosure is CNC-cut and hand-assembled in Tullahoma, Tennessee on ShopSabre CNC routers. Chamber volume, divider placement, cutout geometry, dado joint depth, baffle layer count, dowel placement, and terminal positioning are all held to spec on every unit. Langboard Elite MDF throughout — named, mill-documented, published density and bond specifications.