
$319.99
See if it's really the one
Search with this product to compare it, find similar styles, or turn up something better before deciding.
Performance Optimized Wedge | JL Audio 13W3v3 Single 13.5" Sealed Wedge Enclosure | Rear-Firing Trunk-Load Design for the JL Audio W3v3 1.85 ft³ Gross 1.75 ft³ Net (JL 2Ω Spec) Rear-Firing Wedge 24" × 16" × 10.35/16.2" V-Groove / Dado Built in Tennessee The JL Audio 13W3v3 in JL's Spec-Perfect Sealed Volume The JL Audio 13W3v3 is JL's oversized 13.5" driver — a 600 watt RMS workhorse that moves 54% more air than the 12W3v3, delivering deeper extension and higher output at the same amplifier power level. Available in Single 2-ohm (13W3v3-2), Single 4-ohm (13W3v3-4), and Single 8-ohm (13W3v3-8) configurations, this driver uses JL's DMA-optimized motor, a mineral-filled polypropylene cone, and JL's NBR rubber surround with Floating Cone Attach Method for long-term reliability under sustained daily use. The Performance Optimized Wedge Sealed 13 for JL Audio W3 is engineered to hit JL's exact 13W3v3-2 sealed specification. 1.85 cubic feet gross internal volume minus the 13W3v3's 0.096 cubic foot driver displacement equals 1.754 cubic feet net — matching JL's published 1.750 cubic foot sealed spec for both the 2-ohm and 8-ohm variants. In that alignment, the driver delivers F3 of 37.7 Hz and Qtc of 0.96 — deep, warm, high-impact bass in a trunk-friendly wedge cabinet. 1.85 cubic feet gross = 1.754 cubic feet net after the 13W3v3's 0.096 cubic foot driver displacement. Exact match to JL Audio's published sealed spec for the 13W3v3-2 and 13W3v3-8 (Qtc 0.96, F3 37.7 Hz). The 13W3v3-4 variant also fits this cabinet, running slightly larger than its 1.5 cu ft spec for a Qtc around 0.82. The wedge geometry mounts the woofer on the vertical trunk-lid-side face, firing rearward into the trunk cavity. Trunk-Load Wedge Design Explained This wedge is not a front-firing enclosure. The woofer is mounted on the vertical face that sits at the back of the box, closest to the trunk lid, and fires rearward into the trunk cavity. The angled face is on the opposite side of the box — the side that faces the front of the vehicle — and tucks against the rear seat back. Two different problems solved by one geometry. Seat-Side Face Matches Seat Lean Most factory rear seat backs lean roughly 20 degrees back from vertical. The angled face of this wedge (10.35" at the top, 16.2" at the bottom) matches that lean, tucking against the seat back with no wasted gap. The wedge fills the trunk shelf area behind the seat cleanly. Trunk-Lid-Side Face Fires the Woofer The vertical face on the opposite side of the wedge (24" wide × 16" tall) is where the 13W3v3 mounts. The driver fires rearward toward the trunk lid, using the trunk cavity as an acoustic loading chamber. This is the classic SQ trunk-load install pattern. Trunk Cavity Loading Firing the woofer into the trunk cavity rather than directly into the cabin uses the trunk itself as an extension of the acoustic system. Low frequencies transmit into the passenger cabin through the rear deck, seat back, and cabin boundaries — a smoother, less localized presentation than direct-firing setups. Preserves Trunk Cargo Space The wedge tucks against the seat back where cargo can't be stored anyway. The bottom face sits flat and stable on the trunk floor. Cargo space in front of the wedge (toward the trunk lid) stays usable for daily driving. Engineered to JL Audio's Published Sealed Specification JL Audio publishes different sealed enclosure specs for each impedance variant of the 13W3v3. The 13W3v3-2 wants 1.750 cubic feet net (F3 37.7 Hz, Qtc 0.96). The 13W3v3-4 wants 1.500 cubic feet net (F3 40.4 Hz, Qtc 0.89). The 13W3v3-8 wants 1.750 cubic feet net (F3 37.2 Hz, Qtc 0.96). This cabinet is engineered specifically to hit the 1.75 cu ft target used by both the 2-ohm and 8-ohm variants: 1.85 cubic feet gross minus the 0.096 cubic foot driver displacement equals 1.754 cubic feet net — essentially exact match. What the JL 2Ω Spec Delivers JL engineered the 13W3v3-2 for a Qtc of 0.96 in a 1.75 cubic foot sealed enclosure. That's a higher Qtc than the traditional "flat" 0.707 alignment, giving the driver a warm, impactful, midbass-forward bass character. Combined with the 13.5" cone's deep F3 of 37.7 Hz, this alignment produces a bass presentation that reaches lower AND hits harder than the smaller W3v3 drivers can match — the reason to step up to the 13" is precisely this combination of depth and impact from a single driver. Listeners looking for a flatter, more analytical alignment can use the 13W3v3-4 in this cabinet instead — the -4 in a slightly-larger-than-spec 1.754 volume trends toward Qtc 0.82, still warm but flatter than the -2 and -8. Mounting Geometry The vertical trunk-lid-side baffle is cut to the 13W3v3's exact 12.5625" cutout specification. The 13W3v3's 7.63" mounting depth fits inside the cabinet — internal depth from the vertical baffle to the interior of the angled seat-side face ranges from 10.35" at the top to 16.2" at the bottom, providing ample clearance for the driver's motor and cooling requirements. 8/32 threaded inserts are pressed into the baffle backside for secure driver retention. The 14" outer diameter of the 13W3v3 sits within the 16" tall baffle with adequate clearance for mounting flange. Performance Series Construction, Driver-Specific Tuning Langboard Elite MDF Premium 3/4" MDF panels milled to documented spec — denser and more dimensionally stable than commodity MDF. Less panel resonance, tighter joints, and a longer service life under daily use at the 600 watts RMS the 13W3v3 handles. V-Groove and Dado Joinery CNC-cut V-grooves at every panel intersection let the wedge cabinet fold into its angled shape with maximum glue surface. Dado joints lock the vertical woofer baffle and the angled seat-side panel into the side walls — no fasteners visible from outside, no exposed end grain at joints. 8/32 Threaded Inserts Threaded inserts pressed into the vertical woofer baffle accept stainless steel mounting screws. No stripped pilot holes, no MDF damage from drywall screws, no surprises when the next driver upgrade rolls around. Pre-Wired Terminal Cup Proline X ABS/carbon fiber composite terminal cup, pre-wired with 12-gauge OFC inside the cabinet, with stainless steel hardware accepting both spade and banana terminations on the input side. Every panel is cut on ShopSabre CNC routers in our Tullahoma, TN facility. The angled seat-side panel requires precise CNC compound cuts to hit both the volume target and the mating angles between the top and bottom edges — tolerances that manual fabrication can't reliably hold. Internal volume is verified on every unit to ensure the JL-spec 1.75 cubic foot net target is achieved. Customize Your Build Carpet Finish Dark Gray Trunkliner is the standard durable wrap, matched to most factory trunk and cargo-area carpet tones. Plush Black (+$10) is a deeper, more luxurious nap that pairs well with blacked-out interiors and show builds. Acrylic Insert Color Choose Black, Blue, Red, or White for the baffle insert to match your build. Or skip the insert entirely (-$40) for a clean, understated look. The insert is purely cosmetic — performance is identical across colors. Box-Only or Loaded Add a JL Audio 13W3v3-2 (2-ohm), 13W3v3-4 (4-ohm), or 13W3v3-8 (8-ohm) driver directly to your order and we'll ship the complete loaded system, ready to wire to your amplifier. This cabinet is optimized for the 2-ohm and 8-ohm variants' 1.75 cu ft spec. Already own your 13W3v3? Order the enclosure box-only and drop in the driver you have. Wiring the JL Audio 13W3v3 to Your Amplifier The JL Audio 13W3v3 is a single voice coil driver available in three impedance versions. The pre-wired terminal cup accepts the two-conductor connection via 12-gauge OFC, with stainless steel input hardware. The 13W3v3-2 (Single 2-ohm) presents a 2-ohm load directly to your amplifier — the most common choice, delivering the highest power output from most modern class D monoblocks stable at 2 ohms. The 13W3v3-4 (Single 4-ohm) presents a 4-ohm load — easier on both amp and driver for daily use. The 13W3v3-8 (Single 8-ohm) presents an 8-ohm load — used mainly with high-voltage amp bridges or matched with class AB amplifiers. The 13W3v3 is rated for 600 watts RMS continuous, with JL Audio recommending amplifier power in the 150 to 600 watt RMS range. Aim for a clean, well-regulated amplifier delivering 400 to 600 watts RMS at your chosen impedance for balanced output and long-term reliability. JL Audio's own RD or XD series 600/1 monoblocks are natural matches. Important: JL Audio explicitly recommends against using this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Use your amplifier's active low-pass filter to set the sub's upper cutoff, typically between 80 and 100 Hz for musical accuracy. Built in Tennessee, Backed by Audio Intensity Every Performance Optimized enclosure is CNC-cut, assembled, and finished in our Tullahoma, TN facility. Components are pulled from inventory after your order is placed, then bonded and wrapped — a 2 to 5 business day assembly window before the box ships. No pre-built inventory sitting in warehouses, warping in storage. Each unit is built to order. Backed by a 1-year limited warranty against structural failure and hardware defects. Questions on fitment, wiring, or amplifier pairing? Contact us — we install this gear ourselves, in our own vehicles. JL's Spec Volume for the 13, in a Trunk-Load Wedge 1.75 cubic feet net internal — JL Audio's published optimum sealed volume for the 13W3v3-2 and 13W3v3-8 — in a trunk-friendly wedge geometry that fires the 13.5" cone rearward into the trunk cavity. Deep extension, high impact, precise driver-specific engineering.
Have a question about this?
We currently ship within the US, with more countries coming soon.
Final cost and dates are confirmed at checkout.
🇺🇸 Ship from USA · On Agora since 2025
$319.99