Peavey Classic 30 Guitar Combo Amplifier

DESCRIPTION  Revered by blues, country, and rock players alike, the Peavey Classic 30 all-tube combo amp provides the legendary warm tones that have made Peavey’s Classic Series a staple for guitarists of all genres. At home, on stage, or in the studio, the smooth tube sound and clean melodic power of the Peavey Classic 30 is the perfect complement to your musical journey. Authentic Sound For Country, Jazz, Blues, and Rock n’ Roll players, no other combination of warmth and power rivals the Classic 30. Loaded with (4) EL84 power tubes and (3) 12AX7/ECC83 preamp tubes, the Classic 30 is the best small guitar amp to unlock your tone and captivate your audience. Outfitted with a 12” Celestion Midnight 60 speaker, the warm tones of the legendary Classic Series are at your fingertips. Timeless Classic Since 1973, the Peavey Classic series electric guitar amps have been a trusted choice for professional musicians on stage and in the studio, renowned for their exceptional quality and tone. Developed by founder Hartley Peavey, the Classic Series epitomizes Peavey's commitment to uncompromising quality, rich tones, and extraordinary value. Road Warrior Equipped with 2 channels and a specially designed boost function, this versatile gigging companion is perfectly suited for small to medium-sized venues. Each channel shares EQ, an effects loop, and reverb (all footswitchable). With 30-watts RMS of pure tube power, the Peavey Classic 30 looks and plays the part tastefully appointed with handsome tweed and chrome finishes.  FEATURES  (4) EL84 power tubes and (3) 12AX7/ECC83 preamp tubes Shared 3-band EQ 12” Celestion Midnight 60 speaker Power switch with Pilot Light and Standby Switch Footswitch included SPECIFICATIONS  Power Amplifier Section: Four 6BQ5/EL84’s with 12AX7 driver Rated Power & Load: 30 watts RMS into 16 or 8 ohms Power @ Clipping (Typically): (5% THD, 1 kHz, 120 V AC line) 30 watts RMS into 16 or 8 ohms (Bias must be reduced to measure) Frequency Response: +0, -2 dB, 50 Hz to 15 kHz, @ 20 watts RMS into 16 ohms Hum & Noise: Greater than 80 dB below rated power Power Consumption: 150 watts, 50/60 Hz, 120 VAC (Domestic) Preamp Section: Two 12AX7’s The following specs are measured @ 1 kHz with the controls preset as follows:  Pre & Post (lead) @ 0 Reverb Level @ 0 Bass & Treble EQ @ 12 Middle EQ @ 0 Channel Select Out Boost Switch Out Nominal level is with Input Gain @ 6. Minimum level is with Input Gain @ 12. Preamp Normal Input: Impedance - Very high Z, 470 K ohms Lead Channel:  Nominal Input Level: -40 dBV, 10 mV RMS Minimum Input Level: -70 dBV, 0.3 mV RMS Normal Channel:  Nominal Input Level: -17 dBV, 140 mV RMS Minimum Input Level: -28 dBV, 40 mV RMS Maximum Input Level: 0 dBV, 1.0 V RMS Equalization: (Lead and Normal Channels) Custom bass, middle, and treble passive-type EQ Effects Send: Load Impedance: 1 K ohm or greater Nominal Output Level: -6 dBV, 0.5 V RMS Effects Return:  Impedance: High Z, 2 M ohms Designed Input Level: -6 dBV, 0.5 V RMS (Switching jack provides Effects Send to Effects Return connection when not used.) External Footswitch Function:  Jack 1: Reverb Defeat (when reverb control is raised), Tremolo on/off Jack 2: Normal/Lead Channel Select (when Lead activated), Boost on/off