Lanyard tether kit- with shrink rings and D-Rings LYKT1

TETHER TETHER KIT- WITH SHRINK RINGS AND D-RINGS (Single) - Portable kit used to bring directly to job locations. Contains tethering devices for smaller work activities Features Quantity: Single Heavy duty portable carrying case with bins and flip top lid Standard heat gun required for shrink ring assembly Industries This product is often used in the following industries Construction Utility General Industry   LYKT1 High-Strength Heat-Shrink Tool Attachment Kit — 60 Attachments with Organizer Create secure tether attachment points on compatible hand tools that do not have built-in tether connections. The LYKT1 kit contains 60 high-strength heat-shrink loop attachments in three sizes, organized in a portable compartment case for convenient storage and transport. Each attachment combines heat-shrink material, webbing and a D-ring connection into one assembly. No separate D-ring webbing or tool-attachment tape is required. Kit Contents ● 20 TP2R1X175LPOR attachments 1-inch x 1.75-inch before shrinking Fits tool diameters from 0.36 to 0.75 inch Maximum tool weight: 2.5 lb Maximum tether length: 48 inches ● 30 TP2R15X2LPOR attachments 1.5-inch x 2-inch before shrinking Fits tool diameters from 0.55 to 1.25 inches Maximum tool weight: 4 lb Maximum tether length: 48 inches ● 10 TP2R2X2LPOR attachments 2-inch x 2-inch before shrinking Fits tool diameters from 0.75 to 1.75 inches Maximum tool weight: 5 lb Maximum tether length: 48 inches ● 1 portable organizer for the kit contents Key Features ● 60 high-strength heat-shrink tool attachments in three useful sizes ● Integrated D-ring tether connection ● No separate tool-attachment tape required ● Portable organizer keeps sizes separated and available at the work location ● Designed for compatible tools with abrupt geometry ● Helps prepare tools for dropped-object prevention and controlled-tool programs ● Included attachment models are listed as meeting ANSI/ISEA 121-2023 ● Suitable for industrial maintenance, construction, utilities, power generation, outages and other controlled work environments How to Install a Heat-Shrink Loop Attachment Read the Instructions Read and understand the complete manufacturer instructions before selecting, installing or using an attachment. Inspect the Tool and Attachment Confirm that the tool is clean, undamaged and compatible with this attachment method. Inspect the shrink loop, webbing, D-ring and label. Do not use an attachment with cracks, rips, tears or other damage. Measure the Tool Measure the diameter at the intended attachment location. Select the correct shrink-loop size using the stated diameter range, tool-weight limit and maximum tether length. Confirm Suitable Tool Geometry Select a location where the tool’s ends are larger than the area where the shrink loop will rest. The attachment location must prevent the loop from sliding completely off the tool. Do not use these attachments on straight-shaft tools without suitable abrupt geometry. The manufacturer’s instructions specifically identify cylindrical, hexagonal and square straight-shaft tools, pliers and vise grips as unsuitable applications. Position the Attachment Slide the selected shrink loop over the tool and place it where it will not interfere with normal operation or create another safety hazard. Apply Heat Wear appropriate personal protective equipment. Using a standard heat gun, evenly heat the underside of the shrink loop while keeping the heat source approximately 1 inch away. Then heat the top section. Avoid heating the care label. Do not char or burn the shrink material or webbing. Allow It to Cool Allow the attachment to cool for approximately 30 minutes before testing or use. Check the Installation Pull firmly on the D-ring to confirm a tight installation. Some movement along the straight portion of a compatible tool may be normal, but the tool’s geometry must prevent the attachment from coming off. Inspect Before Every Use Inspect the attachment, D-ring, webbing, tool, tether and anchor point before each use. Immediately remove any damaged or questionable component from service. Important Warnings ● Never use this product on or near rotating equipment. ● Use only on tools with suitable abrupt geometry that prevents the attachment from sliding off. ● Do not exceed the stated tool-weight limit for the selected attachment. ● Do not use a tether longer than 48 inches with these attachments. ● The complete system is limited by its lowest-rated component, including the attachment, tether, connectors and anchor point. ● Do not suspend or intentionally hang a tool from its tether. ● Do not char or burn the shrink material. Burning can produce irritating fumes. ● Use appropriate PPE when operating the heat gun and installing the attachment. ● Keep the attachment away from sharp edges and conditions that could cut, melt or damage it. ● These attachments are for tool tethering only. They are not fall protection, personnel-support equipment or lifting devices. ● Follow the manufacturer instructions and the employer’s approved dropped-object prevention, tool-control and FME procedures. What Is Not Included Tool tethers, wrist cuffs, tool-attachment tape, split rings, loose D-ring attachments, tools, anchors, heat gun and installation PPE are not included unless separately stated on the order. Frequently Asked Questions How many attachments are included? LYKT1 contains 60 high-strength heat-shrink loop attachments: 20 small, 30 medium and 10 large. One portable organizer is also included. Does the kit include tool tethers? No. Tool tethers and anchor points must be selected separately for the tool, attachment rating, work location and approved dropped-object prevention program. Is tool-attachment tape required? No. These high-strength shrink loops combine the heat-shrink body and D-ring connection into one attachment assembly. Can these attachments be used on any tool? No. The tool must fall within the applicable diameter and weight limits and have suitable abrupt geometry that prevents the attachment from sliding off. What heat source is required? Installation requires a standard heat gun. The heat gun is not included. How long should the attachment cool? Allow approximately 30 minutes before testing or using the installed attachment. Are the attachments ANSI compliant? The manufacturer lists each of the three included attachment models as meeting ANSI/ISEA 121-2023 when properly selected, installed, inspected and used according to its instructions.