
$160.43
See if it's really the one
Search with this product to compare it, find similar styles, or turn up something better before deciding.
The LiftMaster CPS-EI connects an approved four-wire monitored sensing edge to a supported LiftMaster Logic commercial door operator. It is an interface in the door’s reversing system, not the sensing edge itself or a universal converter for every safety input. The manufacturer instructions identify specific compatible edge models and wiring arrangements, including a stand-alone-system restriction in the cited installation sheet. Select the interface, edge and operator together, using the applicable current instructions to confirm the complete protection configuration before installation or replacement. Compatibility — Models, Versions and Exclusions Model or selection point Compatibility requirement Supported LiftMaster Logic commercial operators Verify the exact control board and approved CPS-EI wiring diagram. Approved four-wire sensing edges Manufacturer sheet lists 65-ME123 4, 65-ME113 4, 65-8203 2 and 65-8204 4; confirm current edge identification. Two-wire or resistive edges Do not substitute based solely on appearance or terminal count. Gate operators and residential openers No universal compatibility established. Multiple protection devices The cited CPS-EI sheet specifies stand-alone use; do not combine devices without a documented approved configuration. Choose the Interface and Edge as a Complete SystemA sensing edge is only useful when its mechanical installation, electrical interface and operator response work together. Confirm the edge length and mounting requirements with its manufacturer, then have the installer verify the operator’s supported interface. A damaged edge or moving cable can remain faulty after the interface is replaced, so diagnosis should cover the entire connection path rather than only the small electronic module. The green indicator provides a service clue but does not replace a functional reversing test. Follow the current operator and interface instructions for the complete installation, including protection of exposed connections and separation from power wiring. If the intended system uses additional protection devices, resolve that arrangement against the approved documentation before purchase. Do not improvise parallel connections or remove required protection to make a preferred operating mode work. Specifications and Product Identification Specification Details Model CPS-EI Product Commercial Protector System edge interface Edge type Approved four-wire monitored sensing edge Documented platforms Supported Logic commercial door operators Status indication Green LED; functional testing still required Separate requirement Sensing edge, field connections and protective junction box Before Ordering Identify the commercial operator and control-board generation. Confirm the exact approved four-wire sensing-edge model. Review the permitted protection arrangement and current wiring instructions. Inspect the edge, moving cable and field connections before selecting replacement parts. Package Contents and Separate RequirementsThis listing identifies the CPS-EI interface. A sensing edge, coil cord, junction box, field conduit, operator and complete door system are separate requirements unless expressly included in a supplier package. The manufacturer recommends a junction box and states that it is not provided. Confirm the current carton for connection accessories and select the edge itself to suit the approved application and door dimensions. Safety Warnings — Read Before Installation or Service WARNING: Incorrect edge installation or wiring can defeat obstruction detection and expose people to serious injury. Use a qualified commercial door technician. Disconnect applicable operator power before installation. Follow the specified cable protection and separation from power wiring. Never bypass the edge interface or treat an illuminated LED as proof that the door will reverse correctly. Correct any failed functional test before normal operation. Follow the manufacturer’s reversing test and approved operating-mode requirements. Do not combine protection devices contrary to the applicable installation instructions. Related Products and Important Differences CPS-U commercial photo eyes — a separate protection-system alternative where approved; not an instruction to combine them with CPS-EI. DCWALLCTL MAXUM wall controller — a different control accessory for its supported platform; it is not an edge interface or proof of CPS-EI compatibility. Frequently Asked QuestionsIs the sensing edge included?No edge is promised with this interface-only listing. Will CPS-EI work with any two-wire edge?No. It is specified for approved four-wire monitored sensing edges. Can I add it alongside any photo eye?Do not assume that. The cited installation sheet specifies stand-alone use; follow the current approved system configuration. Does a green LED finish the safety test?No. The complete door must perform the manufacturer’s required reversing test. Need Help Confirming the Right Product?Contact Garage-DoorParts.com before ordering. Send the full equipment model, readable part labels and photographs of the installed assembly. Include the dimensions, electrical configuration or accessory details relevant to your project so the listing can be checked against the actual installation.
Have a question about this?
We currently ship within the US, with more countries coming soon.
Final cost and dates are confirmed at checkout.
🇺🇸 Ship from USA · On Agora since 2026
$160.43