Labocosmetica - HPC - Ceramic Coating

DESCRIPTION: Gloss matt paint hybrid nano ceramic coating #HPC paves the way to a whole new category of coatings dedicated to the overcoat. Thanks to its “nano hydro-gel system” technology, it creates a hydrophobic membrane with a polymeric matrix made up of “building blocks”, which form lattices and adhere directly to the surface at room temperature, creating a highly resistant and elastic layer. #HPC is resistant to chemical, saline and uv ray attacks which cause corrosion and non-removable stains it also has antifouling properties its distinguishing feature is its antistatic and antifouling capacity, leaving the car clean for longer. The #HPC coating can be applied alone or as a protective agent on other #Labocosmetica coatings (top coating) this membrane creates a three-dimensional gloss that provides deep shine and enhances the color of the paint. The #Labocosmetica coatings were subjected to different stress tests first in the laboratory and then directly in the field thanks also to the collaboration of different international detailers. We have selected the cities with the most extreme climatic conditions in the world: Dubai (United Arab Emirates) for the scorching heat and its sandstorms, Delhi (India) and Manila (Philippines) for the suffocating smog and the tropical heat, Moscow (Russia) and Gothenburg (Sweden) for the cold and the road conditions, in addition to the major European capitals where the climatic and road conditions are certainly more normal. It should be noted that for the entire duration of the tests it was not always possible to comply with the coating maintenance program recommended by us. This allowed us to verify the condition of the treated surface in the worst situation. With the results of the numerous tests we have made a weighted average where it can be seen that one year of life of our coatings is approximately 15,000 km. Based on this data, we can therefore state that: – Combined with the #SAM, #BLINDO, #STC coatings increases by 20,000 / 30,000 km in terms of duration and performance. Safety: it is PFAS free and complies with the content of volatile organic components (VOCs) according to Directive 2004/42/EC and the method of analysis in accordance with UNI EN ISO 11890-1:2008.   HOW TO USE: SURFACE PREPARATION : An accurate preparation of the surface to be treated is essential for the correct fixing and maintenance of the coating. We recommend that you always observe these simple rules: the surface must be decontaminated and free from any residue; remove old waxes from the surface , sealants or coatings before proceeding; the surface must be perfectly free from surface scratches, marks and stains which, if present, must be removed with a polisher; if you are working with a new car that does not require corrective paint work, proceed with a decontaminating wash to remove any residues from transport; the bodywork must be completely degreased : use # Vèritas in the dilution 1: 5 before applying the coating. This step is mandatory! SUGGESTIONS FOR APPLICATION: Always apply the coating in covered and dust-free environments , never outdoors. We recommend the use of PPE (Personal Protective Equipment) in this case the solvent steam mask. Never work in direct sunlight. Make sure the work area is well ventilated. There are two main factors that influence the application of coatings: temperature and humidity . The higher the temperature and / or humidity , the shorter the coating installation time. We suggest to work on small sections of maximum 50x50cm . It is essential to use correct lighting. Apply the coating using reflected lights. Point your lamp at the wall or ceiling – this will help you spot possible smudges that you will need to remove immediately . The initial fixing time of the #SAM and #HPC coatings of #Labocosmetica with the treated surface is a few minutes : therefore use microfibre cloths to eliminate residues and carry out the finish. Make sure that the car remains in optimal conditions without the risk of rain or sudden changes in humidity: the curing time necessary to allow the partial closure of the coating takes place within 12 hours , while the total one takes place within 36 hours and it is advisable not to wash the car for the first 7/10 days. If you have an infrared lamp, place it at a distance of 50cm for about 15-20 minutes at 60 ° C temperature to fix the coating to the surface. Always respect the application instructions of the individual products.   PRODUCT DETAILS: The #Labocosmetica coatings were subjected to various stress tests first in the laboratory and then directly in the field thanks to the collaboration of different detailers international . We have selected the cities with the most extreme climatic conditions in the world: Dubai (United Arab Emirates) for the scorching heat and its sandstorms , Delhi (India) and Manila (Philippines) ) for the suffocating smog and tropical heat, Moscow (Russia) and Gothenburg (Sweden) for the harsh cold and road conditions, as well as the major European capitals where climatic and road conditions are certainly more normal. It should be noted that for the entire duration of the tests it was not always possible to comply with the coating maintenance program recommended by us . This allowed us to check the conditions of the treated surface in the worst situation. With the results of the numerous tests we have made a weighted average which shows that one year of life of our coatings is approximately 15,000 km.   WARNINGS: P102 Keep out of the reach of children. H304 May be fatal if swallowed and if it enters the respiratory tract. H317 May cause an allergic skin reaction. H412 Harmful to aquatic life with long lasting effects. P210 Keep away from heat sources, hot surfaces, sparks, open flames or other sources of ignition. Not smoking. P261 Avoid breathing mist / vapors / spray. P280 Wear protective gloves / goggles / face protection. P301 + P310 IF SWALLOWED: Immediately call a POISON CENTER / doctor. P305 + P351 + P338 IN CASE OF EYE CONTACT: rinse thoroughly for several minutes. Remove any contact lenses if easy to do. Continue rinsing. P403 + P233 Keep container tightly closed and in a well-ventilated place. Contains: naphtha (petroleum), light alkylation, distillates (petroleum), light hydrotreated