Kvaser Leaf Light Rugged HS

NOTE: This product has been designated Not For New Design (NFND), effective September 27, 2017. We encourage customers to migrate to the newest version of the product, the Kvaser Leaf Light Rv2. Kvaser Leaf Light Rugged HS (with Galvanic Isolation) is a one channel USB interface for CAN. In hostile environments where dust and water are the norm, the IP67 rated housing assures reliable protection. Features Tech Specs Documents Downloads IP67 rated lightweight aluminium housing Polyurethane cabling for extreme environments CAN messages are time-stamped with a precision of 100 microseconds Handles up to 8000 messages per second Supports both 11-bit (CAN 2.0A) and 29-bit (CAN 2.0B active) identifiers Supports data and remote frames Detects error frames Very good EMC performance Fully compatible with all higher layer protocols including J1939 and CANopen Equipped with a 110 cm (44 in.) long USB cable and a 30 cm (12 in.) long CAN cable Interfaces the CAN bus with a 9-pin D-SUB connector Galvanically isolated CAN bus driver Designed for USB 2.0, backward compliant with USB 1.1 Low power-consumption Temperature range -40 °C - +85 °C Quick and easy Plug-and-Play installation 100% software compatible with applications written for all Kvaser hardware with Kvaser CANlib SDK A practically unlimited number of Kvaser Leafs can be connected via standard USB hubs for simultaneous use on a single PC Property Value The information herein is subject to change without notice. Galvanic Isolation Yes Bitrate 5-1000 kbit/s Silent mode No Error frame generation No Error frame detection Yes Weight 100 grams Timestamp resolution 100 On board buffer Yes Maximum message rate, send 8000 Maximum message rate, receive 8000 Sound No Clock synchronization N/A Dimensions (WxLxH) 30x200x20 mm (1.2x7.9x0.8in.) Kvaser Leaf User's Guide User's Guide for the Kvaser Leaf Light Version 11.0.0 Kvaser Leaf Light Rugged HS Datasheet Datasheet for the Kvaser Leaf Light Rugged HS Version 2013 Kvaser Leaf Installation Guide Kvaser Leaf Installation Guide Version 4.1.0 Kvaser DIADEM Driver This free driver for National Instrument's DIAdem supports all CAN hardware from Kvaser. Version 1.0.0 Kvaser Drivers for Windows Windows drivers for all our CAN hardware. Please check release notes for information on which Windows versions are supported. It also contain a driver for the virtual CAN bus. Version 5.6.0 Kvaser Leaf V2 Firmware Firmware Kvaser Leaf Light V2 Version 3.2.302 Kvaser CANKing A free of charge general-purpose CAN bus momnitor. Works with all CAN interfaces from Kvaser. Windows 200 and later recommended. Version 5.3.889 Kvaser CANlib SDK Software development kit - everything you need to develop software for the Kvaser CAN and LIN interfaces. Link libraries, header files, sample programs, Microsoft Visual Basic and Borland Delphi components, documentation, and more. Note: you need to download and install the appropriate device drivers separately Version 5.6.0 Kvaser LabView VI Library for CAN Library for National Instrument's LabView version for all Kvaser CAN hardware. Version 6.1.0 Kvaser Linux Driver and SDK Linux driver and SDK for Kvaser PCIcan/PCIcanx, Kvaser PCIcanII, Kvaser PC104+, Kvaser PCIcanx II, Kvaser USBcan II, Kvaser Memorator*, Kvaser Leaf family, Kvaser Memorator Pro**, Kvaser USBcan Pro and VirtualCAN. For LAPcan and LAPcan II, you should use version 4.2 of the driver. (*) only with USBcanII functionality, (**) only with USBcan Pro functionality Version 5.3.0 Remove old drivers Driver removal program. This program will remove the CAN driver (version 3.2 or older) from your computer. This is a version intended for those who have installed CANLIB 3.2 or older. Use it only if you need to remove an old version of the driver from your computer. Contact technical support if you have any questions. Version 3.9c