INSTEON Micro On/Off Module 2443-222

Turn Any Wall Switch Into an INSTEON Remote Controllable Switch Overview Add remote control to virtually any switch or outlet The smallest inline module ever! Fits into almost all boxes Turn your antique, custom color or non-standard wall switches into home automation switches Wire in behind your existing switches, outlets and above your light fixtures Sense wires allow for control via a connected, hard-wired switch Compatible with latching switches as well as single momentary and dual momentary switches Essential Info Adding remote control to wired lights usually means replacing switches, not any more. With INSTEON's new dual-band Micro On/Off Module, you can keep your antique, toggle or decorative wall switches while adding the same remote control functionality of SwitchLinc. This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch by way of sense wires. Connect the sense wires to any style wall switch to match any type of designer theme (antique, push-button, metal, etc.) Micro On/Off is so tiny that it can be installed as an in-line module within a fixture box, providing remote control without having to run wires to a wall switch. INSTEON also offers a Micro Dimmer Module and a Micro Open/Close Module. More Info INSTEON Micro On/Off is compatible with latching, single momentary and dual momentary switches. By default, it comes programmed for latching switches such as paddles and toggles; it is easily configured for single and dual momentary switches with a simple reprogramming procedure during installation. Due to its hidden nature, we highly recommend using a home management controller INSTEON Hub to manage Micro Open/Close. General Product Name: INSTEON Micro On/Off Brand/Manufacturer: INSTEON Manufacturer Product No.: 2443-222 UPC: 813922012736 Warranty: 2 years, limited INSTEON INSTEON: Controller and responder Maximum links/scenes: 400 Status LED: Green when load is on, red when load is off, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software), Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software) LED brightness: Adjustable from off to 100% bright Local control: Yes Commands supported as controller: On, Off, Fast on, Fast off, Begin brighten, End brighten, Begin dim End dim Commands supported as responder: On, Off, Fast on, Fast off, Beep Software configurable: Yes RF range: 150 feet open air (may vary due to local interference) Phase detect beacon: Yes X10 support: Yes X10 addresses: Any 1 of 256 (unassigned by default) INSTEON device category: 0x02 switched lighting control (all frequencies) INSTEON device subcategory: 2443-222 (915MHz), 0x2F Mechanical Mounting: Behind switch or outlet, or above light fixture in single-gang electrical box Wire connections: Sense 1 (yellow): 24 AWG, 0.205mm², Sense 2 (purple): 24 AWG, 0.205mm² Screw clamp connections: Line, Load 1, Load 1 (second terminal), Neutral Case color: White Set button: Yes Plastic: UV stabilized ABS+PC Beeper: Yes Beep on button press: Optional (off by default), requires software to enable LED: 1 RGB Dimensions: 1.8”H x 1.8”W x 0.7”D Weight: 2.52 oz Operating environment: Indoors Operating temperature range: 32° to 104°F (0° to 40°C) Operating humidity range: 0-90% relative humidity Storage temperature range: -4° to 158°F (-20° to 70°C) Electrical Voltage: 100VAC to 240VAC Frequency: 50/60Hz auto-detected at power-up Load types: Resistive, Inductive/capacitive, Low voltage halogen Hardwired remote control: Yes, either latching or momentary switches supported Retain all settings without power: Yes, saved in non-volatile EEPROM Standby power consumption: <1W Safety approved: ETL, CE, C-Tick Certifications: FCC, UL, IEC, EN FCC ID: SBPMM01