INSTEON Micro Dimmer Module 2442-222

Turn Any Wall Switch Into an INSTEON Remote Controllable Dimmer Overview Wires in behind your existing switches or fixtures Sense wires allow for control via a connected, hard-wired switch Compatible with latching, single momentary and dual momentary switches Programmable on-level and ramp rate Essential Info Adding remote control to wired lights usually means replacing switches, not any more. With INSTEON's new dual-band Micro Dimmer Module, you can keep your existing antique, toggle or decorative wall switches while adding the customizable, dimmable remote control functionality of a SwitchLinc Dimmer. Customize your lights with a preset brightness level and ramp rate, then control it from any INSTEON controller. This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch by way of sense wires. Connect the sense wires to any style wall switch to match any type of designer theme (antique, push-button, metal, etc.) Micro Dimmer is also so small that it can be installed as an in-line module within a fixture box, providing remote control dimming without having to run wires to a wall switch. INSTEON also offers a Micro On/Off Module and a Micro Open/Close Module. More Info INSTEON Micro Dimmer is compatible with latching, single momentary and dual momentary switches. By default, it comes programmed for latching switches such as paddles and toggles; it is easily configured for single and dual momentary switches with a simple reprogramming procedure during installation. Due to its hidden nature, we highly recommend using a home automation controller to manage Micro Open/Close. General Product Name: INSTEON Micro Dimmer Brand/Manufacturer: INSTEON Manufacturer Product No.: 2442-222 UPC: 813922012705 Warranty: 2 years, limited INSTEON INSTEON: Controller and responder Maximum links/scenes: 400 Load brightness levels: 32 locally (256 with software) Status LED: Green when load is on, red when load is off, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software),Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software) LED brightness: Adjustable from off to 100% bright Local on-level: Adjustable from 32 fixed brightness levels or resume dim Local ramp rate: Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 9 minutes with software) Local control: Yes Commands supported as controller: On, Off, Fast on, Fast off, Begin brighten, End brighten, Begin dim, End dim Commands supported as responder: On, Off, Fast on, Fast off, Begin brighten, End brighten, Begin dim, End dim, Incremental brighten, Incremental dim, Beep Software configurable: Yes Ramp Rates (full-ON to full-OFF): 0.125 to 9 seconds if programmed locally, 0.125 seconds to 8 minutes if programmed remotely via software RF range: 150 feet open air (may vary due to local interference) Phase detect beacon: Yes X10 support: Yes X10 addresses: Any 1 of 256 (unassigned by default) INSTEON device category: 0x01 dimmable lighting control (all frequencies) INSTEON device subcategory: 2442-222 (915MHz), 0x35 Mechanical Mounting: Behind switch or above light fixture in single-gang electrical box Wire connections: Sense 1 (yellow): 24 AWG, 0.205mm, Sense 2 (purple): 24 AWG, 0.205mm Screw clamp connections: Line, Load, Neutral 1, Neutral 2 Case color: White Set button: Yes Plastic: UV stabilized ABS+PC Beeper: Yes Beep on button press: Beeps when button is pressed or connected switch is tapped (must be enabled via software) LED: 1 RGB Dimensions: 1.8"H x 1.8"W x 0.7"D Weight: 2.52 oz Operating environment: Indoors Operating temperature range: 32° to 104°F (0° to 40°C) Operating humidity range: 0-90% relative humidity Storage temperature range: -4° to 158°F (-20° to 70°C) Electrical Voltage: 100VAC to 240VAC Frequency: 50/60Hz auto-detected at power-up Load: Min. 5W, Max. 200W (at 240VAC), Min. 5W, Max. 100W (at 140VAC) Load types: Incandescent Hardwired remote control: Yes, either latching or momentary switches supported Retain all settings without power: Yes, saved in non-volatile EEPROM Standby power consumption: <1W Safety approved: ETL, CE, C-Tick Certifications: FCC, UL, IEC, EN FCC ID: SBPMM01