ICC 7022 COOL WHITE

Introducing Cool White™, A New Concept In White Inks! International Coatings has formulated a white ink that offers superior performance over any other white ink we’ve tested. Our challenge was to create a breakthrough ink that is truly unique, not just another “me-too” ink. Meet Cool White™ 7022! Printers who beta-test the ink love its creamy texture, soft feel, quick flash and opacity. Here are the ink’s other ‘cool’ characteristics: As part of our new FlexCure™ line, Cool White’s ‘flexible’ curing range of 275°F/135°C to 325°F/163°C make it ideal for printing on a variety of substrates. Cool White™ is low-bleed, low-tack and fast flashing. The ink is easy to print, creamy, with a great body. It prints equally well on automatics as on manuals. Cool White™ offers superior performance on a variety of substrates, including hard-to-print synthetic fabrics such as nylon bags, non-woven polypropylene, and polyester sheathing. When using Cool White™, the resulting prints are soft and supple with great drape. Features FlexCure 275-325F Bleed resistant with excellent opacity Mesh: 60 to 230  Fast Flashing Substrates: 100% cotton, Cotton/Poly blends, Polyesters, Non-woven Polypropylene Flash Cure Tips 7022 Cool White™ will spot dry, with a very low after flash tack. Dwell time is dependent on the spot dryer used. In some cases, you may have to lower the heat of the spot cure unit because too much heat may actually make the ink tacky. When you spot dry, you are only partially fusing or gelling the surface of the ink. The ink should be just dry to the touch, with no lift off, but not totally fused. Totally fusing the underprint white may cause inter-coat adhesion problems with the inks printed on top of the white ink. Final fusing or curing should occur in the dryer. Printing Tips 7022 Cool White™ is an ultra low bleed ink, not a non-bleed ink. On some types of fabric, bleeding or dye migration may occur. Always test print the fabric to be printed before beginning production. It is best to do some long term testing on fabrics to determine if they are going to bleed. Bleeding or dye migration may not occur right away. Cool White™ was formulated to make printing opaque white easy. Hand printing is less tiring because less squeegee pressure is needed. The result is increased operator performance. Automatic equipment can be adjusted to lower squeegee pressure settings, thus improving screen life, squeegee durability, and overall print quality. Cool White™ is part of the FlexCure™ line of products, which gives you a flexible curing range. Cool White™ can be cured from 275°F to 325°F (135°C to 163°C), giving the operator greater flexibility and energy savings. Cool White™ compared to other opaque whites, prints so easily that you will find that a finer screen mesh can be used with the same opacity as a lower, more open mesh. This means less ink will be used; a real money saver in terms of ink usage and cost per print. It also means a softer hand on flashed fabrics. Adding any reducers or additives can lower bleed resistance, opacity, or increase cure times of ink. STIR the ink prior to printing on press and after addition of reducers or additives. Test dryer temperatures and wash test printed product before and during a production run. Tech Specs RECOMMENDED FABRICS 100% Cotton, 50/50 Cotton/Polyester Blends, Some polyester & Nonwoven polypropylene bags (NPB) INK APPLICATION White should be used right from the container without any modications ADDITIVES If modification is necessary, use 1% to 10% by weight of 1099 Low Bleed Curable Reducer SCREEN MESH: 60-230  EMULSION: Any direct or indirect emulsion or capillary SQUEEGEE: 65-75 durometer, Sharp edge CURE TEMPERATURES 275F to 325F the entire ink film. Fusing at a lower temperature may require a longer dryer retention time. CLEAN UP: Any eco-friendly plastisol screen wash STORAGE OF INK CONTAINERS 65º to 90ºF Avoid storage in direct sunlight Keep containers well sealed TDS / SDS Download ICC White Comparison Sheet Download TDS: Technical Data Sheet Legal Disclaimer Recommendations and statements made are based on International Coatings’ research and experience. Since International Coatings does not have any control over the conditions of use or storage of the product sold, International Coatings cannot guarantee the results obtained through use of its products. All products are sold and samples given without any representation of warranty, expressed or implied, of tness for any particular purpose or otherwise, and upon condition that the buyer shall determine the suitability of the product for its own purpose. This applies also where rights of third parties are involved. It does not release the user from the obligation to test the suitability of the product for the intended purpose and application.