TF-19 WASP Gen2: Flamethrower Drone Attachment

FAQ What drones is the TF-19 compatible with? The TF-19 is designed to be broadly adaptable — it mounts to most heavy-lift cinema and industrial drone platforms with minimal user fabrication. Recommended platforms include: DJI S1000 DJI Matrice 600 / M600 Pro Most other heavy-lift drones designed to carry gimbal or cinema-camera payloads The TF-19 mounts via two 12mm-OD × 500mm rods (included), spaced approximately 195mm apart at the drone interface. This is the same rail standard used by gimbal and camera mounts on most heavy-lift drones, which is why drone-side hardware usually already exists for it. The included sliding rail clamp lets you adjust position along the rods to balance the system over your drone’s center of gravity, and slide the assembly forward for ground refueling without removing it. Note: drone payload capacity should be 10 lbs or more. The TF-19 is ~5 lbs empty, but a full 1-gallon gasoline tank brings total flight weight close to 10+ lbs. What’s included? Does this come with a drone? The drone is NOT included. The TF-19 is an attachment only. You’ll need a heavy-lift drone with at least 10 lb payload capacity to operate it (see compatibility above). Each TF-19 ships with: TF-19 WASP Gen 2 attachment, fully assembled Two 12mm-OD × 500mm mounting rods Instruction and spec sheet What are the performance specs? Max range: 30 ft (20% greater than Gen 1) Fuel capacity: 1 gallon Continuous trigger time: ~100 seconds per fill Empty weight: 5.08 lbs (7% lighter than Gen 1) Ignition: Plasma arc — instant-on spark electrodes Mounting: Two 12mm-OD × 500mm rods, ~195mm spacing What fuel does the TF-19 use? The TF-19 runs on standard gasoline — available at any gas station. That’s all most operators need. Some users mix in up to 50% diesel with the gasoline to slow the burn — diesel is oilier and clings to surfaces better. For prescribed burns, brush clearing, and most agricultural work, gasoline alone is the simplest fuel. Note: like the ARC, the TF-19 is not napalm-compatible. It uses a fuel-pump-driven delivery system, which can’t run thickened fuels. If napalm capability is important to you, look at our X15 or XL18 — both use a CO2-propellant design and are napalm-compatible. How long does shipping take, and what does it cost? Free UPS Ground shipping on the TF-19 within the U.S. In-stock units ship the same or next business day from our facility in Cleveland, Ohio, with most U.S. deliveries arriving in 1–5 business days. Tracking is emailed when the order ships. Is the TF-19 legal in my state? Flamethrowers are legal federally in the United States. The only state-level restriction we observe in shipping: we do not ship to Maryland. For more details, visit our FAQ page. Flamethrowers are legal federally in the United States. The only state-level restriction we observe in shipping: we do not ship to Maryland. For more details, visit our FAQ page. TF-19 WASP Gen 2 Remote ignition for aerial and ground targets — now with improved performance. Made in USA · Free Shipping · Lifetime Warranty Made in USA · Free Shipping · Lifetime Warranty Aerial Firepower, Engineered. The TF-19 WASP Gen 2 is a drone-mounted flamethrower attachment built for remote ignition of aerial and ground targets. Industrial agriculture, wildland fire management, power-line clearing, pest control, and entertainment SFX all become safer and more efficient when the operator stays on the ground. 30 ft max range (20% greater than Gen 1) 1-gallon fuel capacity · 100 seconds trigger time 5.08 lbs empty — 7% lighter than Gen 1 Slide-mount on 12mm rods · works with most heavy-lift drones Plasma arc ignition · runs on standard gasoline Max Performance Engineered for reliability and reach — the Gen 2 platform delivers more range, less weight, and faster ignition. 30ft Max Range Shoot up to 30ft streams of fire — 20% more than Gen 1 7% Lighter Just 5.08 lbs empty — minimal payload strain, maximum flight efficiency Plasma Arc Ignition High-temp instant-on spark electrodes keep it lit Built For The Job The TF-19 brings precision firepower to jobs that are dangerous, expensive, or simply impossible to do on foot. Power Line Clearing Burn off vegetation and debris from utility lines without crews on the ground. Pest Management Eliminate hard-to-reach nests and infestations from the air. Fire Breaks & Back-Burns Wildland firefighting crews can ignite remote-controlled burns without entering difficult terrain. Agricultural Burns Efficient remote ignition for field management and crop residue clearing. Fight Fire With Fire Forest fire management and prevention is both costly and dangerous. Wildland firefighting crews can avoid difficult terrain and adverse conditions while using the TF-19 to ignite remote-controlled burns. Easy Setup, Stable Flight Start flying quickly with the WASP system. Slide the assembly along the included 12mm rods to balance over your drone’s center of gravity. Need to refuel? Slide the system forward on the rods for easy ground access to the 1-gallon tank, then slide it back into flight position. Built For Heavy-Lift Drones The TF-19’s 12mm-rod mounting interface uses the same standard as gimbal and cinema-camera systems on most heavy-lift platforms — including the DJI S1000, M600, and similar industrial drones. Most operators are flying with hardware that already accepts the TF-19 with little to no fabrication. What’s in the Box? Everything you need to mount and fly: TF-19 WASP Gen 2 attachment, fully assembled Two 12mm-OD × 500mm mounting rods Instruction and spec sheet Get Fired Up The TF-19 WASP Gen 2 is built for industrial-grade operations — efficient, adaptable, and ready to deploy on the platforms you already fly. Used By TF-19 vs. The Rest of the Lineup See how the TF-19 stacks up against the X15, XL18, ARC, and the rest of the Throwflame lineup. Compare All Flamethrowers