Discontinued - DTF with DTG Production Bundle

Option 1 (Kothari for Epson F2100) Includes: Vastex D1000 Entry Level Infrared Dryers 26" Belt x 4' Long Ecofreen Mister-T Cyclone Automatic DTF Powder Applicator 14x16 Ecofreen Transfer Film (Hot Peel) for Direct to Film - Sheets DTF Station Hot Melt Powder for Direct to Film - 1kg AA Platen Grip Strips for DTG Transfer (DTF) - 6" x 25' Kothari Print Pro for Epson F2100 - NeoRip F2100 Software DTF Station Proxima Semi-Auto Dual Heat Press California Air Tools 10020C Ultra Quiet, Oil-Free and Powerful Air Compressor, 2 HP Price: $20,876.83   / Saving: $3,684.15 Option 2 (Kothari for Epson F3070) Includes: Vastex D1000 Entry Level Infrared Dryers 26" Belt x 4' Long Ecofreen Mister-T Cyclone Automatic DTF Powder Applicator 14x16 Ecofreen Transfer Film (Hot Peel) for Direct to Film - Sheets DTF Station Hot Melt Powder for Direct to Film - 1kg AA Platen Grip Strips for DTG Transfer (DTF) - 6" x 25' Kothari Print Pro for Epson F3070 - NeoRip F3070 Software DTF Station Proxima Semi-Auto Dual Heat Press California Air Tools 10020C Ultra Quiet, Oil-Free and Powerful Air Compressor, 2 HP Price: $21,896.83   / Saving: $3,864.15  Vastex D1000 Entry Level Infrared Dryers 26" Belt x 4' Long ** Only ships to continental U.S. ** SMART: PTFE coated fiberglass belt with tracking system BELT WIDTH (max garment width): 26″ (66 cm) HEATER WIDTH: 20″ (51 cm) ADJUSTABLE: Speed, temperature, heater height and tilt FAST: 110+* shirts per hour with plastisol and 50+* with discharge PRECISE: Powerful infrared heater with tight coil pattern and heat shields VALUABLE: Best warranty, high quality, exceptional service COMPACT: Total footprint is about 10 sq.ft (3 sq.m) OPTIONAL: 10″ front conveyor extension Dense coil pattern, heater shields and a 6.35 watt per sq in (0.98 watt per sq cm) infrared heater eliminate hot and cold spots and provide the power you need to get the job done. With a 26 in. (66 cm) wide by 46 in. (116.8 cm) long conveyor belt, the D-1000 Compact Infrared Conveyor is sized to accommodate wider jackets and sweats, and wider printed images, than a Vastex sub-compact D-100 Conveyor Dryer with 18 in. (46 cm) wide belt. An available 10 in. (25.4 cm) front conveyor extension increases the standard infeed of 15 in. (38.1 cm) to 25 in. (63.5 cm) for loading of heavier and larger garments. At 46 in. (116.8 cm) long and 32 in. (81.3 cm) wide overall, the unit fits on tabletops or on utility carts with tops as small as 30 in. (76.2 cm) square, and is available with an optional S1-27 mobile stand shown at right. It is also suitable for mobile screen printers to power on site using a small generator at fairs, concerts, trade shows and other events where larger garments as well as tees may be screen printed. It is available in 120V or 240V models equipped with a 20 in. (50.8 cm) wide by 16 in. (40.6 cm) long, 2050 watt heater that carries the same 15-year warranty as all Vastex infrared heaters. Variable controls for both heat intensity and conveyor speed allow fine-tuning of the drying process according to ink type, ink coverage, desired cure temperature, and rate at which items are being printed. The heater can be raised, lowered and pivoted using lock knobs on the sides of the heating chamber according to the thickness of printed garments and/or the angle of printed images on irregularly shaped items, for uniform curing of the printed area using minimum energy. Heater shields are included as standard to maximize edge-to-edge temperature consistency for increased image quality. The compact unit is CE certified and shippable worldwide via UPS, FedEx, DHL and other small package carriers. Vastex D1000 Entry Level Infrared Dryers Manual Vastex D1000 Entry Level Infrared Dryers Info ------------------------------------------------------- Ecofreen Mister-T Cyclone Automatic DTF Powder Applicator Mister T Cyclone Brochure Mister T Cyclone: for use with DTG Printers Features: Consistent Applying Auto Refilling the Powder Less Noise No Need Air Compressor Auto Start with Step Pedal Trigger or Button Easy Control Panel Laser Sensor Heavy Duty Wheels Specifications: Dimensions: 26 inch (W) x 47.2 inch (L) x 76.4 inch (H) (66 cm(W) x 120 cm(L) x 194 cm(H)) Weight: About 150 kgs (330.7lb) Conveyor Belt: 45 cm x 110 cm (17.7 inch x 43.3 inch) Lap Time:  Standard : 14 sec High Production : 8 sec Power Supply: Free Voltage (110V, 30amps) Packing (Wooden Pallet): 36 inch(W) x 57 inch(L) x 80 inch(H) (92 cm(W) x 145 cm(L) x 204 cm(H)) ------------------------------------------------------- California Air Tools 10020C Ultra Quiet, Oil-Free and Powerful Air Compressor, 2 HP The CALIFORNIA AIR TOOLS 10020C Ultra Quiet & Oil-Free Air Compressor is designed to be one of the quietest  2.0 Hp air compressors in the industry having only 70 decibels of sound.  Looking for best practice tips on using this air compressor and more? Look here! Specifications: 2.0 HP (Rated/Running) 10 Gallon Steel Tank 6.40 CFM @ 40 PSI 5.30 CFM @ 90 PSI Features: Ultra Quiet -  Only 70  decibels Oil-Free Pump – Cleaner air for better tool operation. Less maintenance and Costs. Two pressure control gauges  Two - 1/4″ Industrial female quick connectors Easy Start Valve - For Less Starting Amperage Condor Pressure Switch Thermal Overload Protector 125 PSI  Maximum Pressure  110v / 60 hz Low Amp Draw - 14 Amps  Dedicated 15 amp outlet -14 gauge 25ft cord - Min. 5500 Watt Generator Time to fill tank from empty to full - 120 Seconds  Recovery time from 95 PSI to 125 PSI - 25 Seconds Duty Cycle - 70/30  Maximum continuous running 30-60 min. (Depending PSI & CFM) Less heat which dissipates more efficiently 10 Gal. Steel Air Tank With Wheel Kit - Easy to move around. L (16") x W (15.1") x H (35.9") 82.5 lbs 1 Year Limited Warranty Comes complete with Wheel Kit & Two Air Filters UL Certified   ------------------------------------------------------- 14x16 Ecofreen Transfer Film (Hot Peel) for Direct to Film - Sheets NOTE: All Ecofreen films are NOT compatible with STS Mutoh Printers and Prestige High Viscosity DTF Ink Not compatible with Prestige A3+ Desktop DTF Printer. Actual Measurement can be slightly different on each batch. for 16x20: 15.75" x 19.75" for 14x16: 14" x 15.75" Features: After baking the powder, solid white for more vibrant colors Even and regular particles for fine graphic quality and good adherence Finely coated film for no pinholes! Instructions: Print the image onto the matte side of the film in mirror mode. (CMYK>>White Ink) Apply hot melt powder evenly and remove the excess powder. Use a Seismo Shaker unit - like the Seismo S20 - to apply powder with ease. Hover with a heat press to bake the hot melt powder. (320°F, 3-4min). Or use a curing oven (300-315°F, 1min). Transfer the image by heat press at 285°F for 10sec with medium pressure. Remove the film immediately (gently). Heat press again at 285°F for 5sec with medium pressure to enhance softer hand feel and to improve washing durability. *This product has no affiliation with Epson and is not endorsed by Epson. *Settings and directions to print DTF with your F2000/2100 using Garment Creator* The basic concept for DTF is to print CMYK first then WHITE on top of it. ALWAYS MIRROR YOUR IMAGE FIRST! Most of you will be printing onto standard A3 and A4 sheets. Utilize every inch of space as you can to save on time and cost of materials. We call that gang sheeting. One benefit of GC is that it allows multiple images to be uploaded at the same time for printing. Those who order Plastisol Transfers will already know this. The two most common platens I use are 10 x 12 (A2) and 16 x 20 (A3). I place the sheet towards the top middle as a guide and measure how much empty space I have on the sides and bottom because the sheets will be smaller than your platen. I use tape to hold in at least 2 corners to prevent the sheet from shifting while printing. Using GC for DTF is very much the same as with DTG. The only difference is you are reversing the cmyk/white color process and mirroring your image. If your image has black in it then click on Black Garment. That will prevent GC from printing black unnecessarily. For all other colors including white, use (Dark Color). After selecting the proper color choice, you need to tinker with your color and white levels. For me personally I use level 2 for color and level 1 for white. I leave ink density to zero. And make sure you leave enough time in between passes in Pause between Passes (sec). This is very important. I like to choose 30-60 seconds Under White Management it is very important to check “OFF” first before you print your CMYK pass. This will allow your color layer to go down first. After your color pass is done then you go back to white management and click “ON”. Be sure you have enough seconds in your “Pause between passes (sec)” or else your printer will print another CMYK pass right after your white pass. YOU DO NOT WANT THAT! So you MUST manually press cancel on your printer before it does so. Unfortunately, Garment Creator was not designed for DTF so it is necessary to turn white on and off for every print you do. WARNING Powder should NOT be applied on the printer platen. It needs to be applied AWAY from the printer. Application near the printer increases the risk of printer damage if the printer "breathes" in the adhesive powder into the intake fan by the electronics near the back of the machine. Damage to the printer for inappropriate use may not be covered under warranty. Please wear Personal Protective Equipment (eyeglasses, mask, and gloves) when working with DTF products. The fumes from curing the powder can be hazardous. NOTE DTF (Direct To Film) products works with almost all types of fabrics including 100% polyester with good quality results! Ecofreen Transfer Film does not require pre-treatment and it uses minimum 75% less DTG inks on to get good quality. The designed fabrics or printed shirts have a good wash characteristics. The fabric has very slight hand feel touch. The process is much faster than Vinyl printing (Vinyl Printer).   ------------------------------------------------------- DTF Station Hot Melt Powder for Direct to Film Hot Melt Powder Material Safety Data Sheet Formulated for use during DTG Transfer (DTF), DTF Station adhesive powder is a crucial part of any DTF printing pipeline. Cover your DTG Transfer media with this powder to allow for optimal press. Use for 100% cotton, polyester, nylon, and more! Features: After baking the powder, solid white for more vibrant colors Even and regular particles for quality graphics and good adherence Finely coated film means no pinholes! Sizes: 1 lb 1 kg 20 kg Instructions (for use with DTF Station Hot Peel film): Print the image onto the matte side of the film in mirror mode. (CMYK>>White Ink) Apply hot melt powder evenly and remove the excess powder. Use a Seismo Shaker unit - like the Seismo S20 - to apply powder with ease! Hover with a heat press to bake the hot melt powder (340°F, 5min).  Or use a curing oven (300-315 °F, 1min). Transfer the image by heat press at 330°F for 15sec with medium pressure. After the first press,  Option 1: Wait for 4-6 seconds and remove the film gently  Option 2: Rub the top surface with a cloth to remove some heat and peel off the film gently Heat press again at 330°F 5-10sec with medium pressure to enhance softer hand feel. *This product has no affiliation with Epson and is not endorsed by Epson. *Settings and directions to print DTF with your F2000/2100 using Garment Creator* The basic concept for DTF is to print CMYK first then WHITE on top of it. ALWAYS MIRROR YOUR IMAGE FIRST! Most of you will be printing onto standard A3 and A4 sheets. Utilize every inch of space as you can to save on time and cost of materials. We call that gang sheeting. One benefit of GC is that it allows multiple images to be uploaded at the same time for printing. Those who order Plastisol Transfers will already know this. The two most common platens I use are 10 x 12 (A2) and 16 x 20 (A3). I place the sheet towards the top middle as a guide and measure how much empty space I have on the sides and bottom because the sheets will be smaller than your platen. I use tape to hold in at least 2 corners to prevent the sheet from shifting while printing. Using GC for DTF is very much the same as with DTG. The only difference is you are reversing the cmyk/white color process and mirroring your image. If your image has black in it then click on Black Garment. That will prevent GC from printing black unnecessarily. For all other colors including white,  use (Dark Color). After selecting the proper color choice, you need to tinker with your color and white levels. For me personally I use level 2 for color and level 1 for white. I leave ink density to zero. And make sure you leave enough time in between passes in Pause between Passes (sec). This is very important. I like to choose 30-60 seconds Under White Management it is very important to check “OFF” first before you print your CMYK pass. This will allow your color layer to go down first. After your color pass is done then you go back to white management and click “ON”. Be sure you have enough seconds in your “Pause between passes (sec)” or else your