decco Microtop Wall Ready to Use kit

heydecco — MicroTop Wall System MicroTop Wall Ready-to-Use Kit A streamlined, pre-measured microcement kit designed specifically for wall applications — primer, fine coat, toner, and 2-component sealer, all included. MicroTop Wall RTU applies directly over smooth absorbent surfaces like plaster, drywall, paint, and tile — with no demolition required. Lighter and simpler than the floor kit: no base coat needed, same seamless result in 2 coats. Key Benefits Wall-specific formula Fine-grade microtopping optimized for vertical surfaces — no heavy base coat needed. No demolition required Applies directly over plaster, paint, drywall, and tile. Just 1–3mm thick. 40 colors · 4 intensities Full Classic and Nature collections. Use 100%, 75%, 50%, or 25% of toner pack to control depth. Complete pre-measured system Everything included — primer, fine coat, WB color toner, and 2-component Ultra Seal. What's in the Kit decco Primer Ready to use Consolidates surface and reduces substrate absorption. Roll on 1 coat, dry 30–40 min. Clean roller immediately with water. MicroTop Fine Coat Ready to use — Fine grade Smooth fine-grade microtopping. Apply 2 coats with a steel trowel, sanding between each coat. WB Color Toner Pre-measured · UV stable · Integral color Shake before use. Add full pack to Fine Coat and mix mechanically until a homogeneous paste is achieved. Ultra Seal Matte 2-component PU sealer Mix Part A + B at 10:1 ratio. Pot life 30–40 min once mixed. Apply 2 coats with roller, 4–6 hrs between coats. Color Toner Mixing Intensity guide — proportion of full toner pack to use: 100% — Full intensity (standard application) Full pack 75% — Rich, slightly softened tone ¾ pack 50% — Medium, airy tone ½ pack 25% — Light, barely-there wash ¼ pack Applications Accent & feature walls Bathroom & shower walls Kitchen backsplashes Over existing tile Drywall & plaster Sample boards & mockups Application Process Step Process 1 Clean surface, leaving it free of dust and grease. Place adhesive tape to delimit the area. 2 Roll on decco Primer. Allow 30–40 minutes to dry. Clean roller immediately with water. 3 Shake toner pack. Add to MicroTop Fine Coat. Mix mechanically until homogeneous. 4 Apply 1st coat with a steel trowel in thin passes. Use spatula to load trowel, or apply with roller then trowel down. 5 Let dry. Sand with 220 grit. Clean and vacuum thoroughly. 6 Apply 2nd coat of Fine Coat. Two coats mandatory for solid, uniform finish. 7 Let dry. Sand with 320 grit. Clean and vacuum thoroughly. 8 Wait 4–6 hrs. Mix Ultra Seal A+B at 10:1 (pot life 30–40 min). Apply 2 coats, 4–6 hrs between each. 9 Allow 7 days before wetting or cleaning the sealed surface. Technical Data Property Details Product type Ready-to-use microcement — Fine grade Coverage (Fine Coat) 0.025 lb/sq ft per coat Coverage (Ultra Seal) 0.01 lb/sq ft per coat Coats required 2 minimum Sanding — 1st coat 220 grit sandpaper Sanding — 2nd coat 320 grit sandpaper Ultra Seal mix ratio 10:1 (Part A : Part B) Ultra Seal pot life 30–40 minutes after mixing Dry between sealer coats 4–6 hours Full cure before wetting 7 days Compatible substrates Plaster, paint, drywall, tile, concrete Available colors 40 colors · 4 intensities each Downloads Technical Data Sheet — Microcement in Walls PDF — surface prep, application steps, coverage data Color Chart 2026 — 40 Colors PDF — Classic & Nature collections with color intensity guide Product Catalog PDF — full heydecco product range & system overview Always complete the system with 2 coats of Ultra Seal Matte — this protects the microcement and ensures long-term durability. Wait 7 full days before exposing the surface to water or cleaning products.