Daitoku Purple

ALWAYS TEST BEFORE FULL APPLICATION DESCRIPTION Daitoku Purple is a purple based bright purple violet pigment and part of our Glow Series line. Expose the Glow in the Dark pigments to light in order to charge the pigments. GLOW TIME PER CHARGE - Unlike other brands, our Glow in the Dark pigments should last 8-10 hours per charge. Mixing other pigments with the Glow in the Dark pigments will work BUT they will significantly decrease the ability to glow. Compared to normal pigments, Glow in the Dark pigments have a heavier density and requires a smaller jar which may make it appear there's less. Glow in the Dark mica powder is ideal for DIY craft use, such as, epoxy, resin, woodworking, pen blanks, plastics, slime, watercolors, cosmetics, fishing lures, bath bombs, jewelry, melt and pour, acrylic, polish, candle making, and MUCH more.  INGREDIENTS & PARTICLE SIZE Particle size              30-50   μm Ingredients               Strontium Aluminate, Polyurethane-11, Maganese Violet Heat Threshold         752 °F - 1112 °F MIXING TIPS FOR GLOW IN THE DARK Are you having a difficult time mixing the pigments or just find yourself stirring and stirring? Or even worse, finding tiny specs in your finished product? This is mostly the cause of not mixing and breaking down the pigment enough. Due to the granular nature of specialty pigments such as neons, glow in the dark, etc. these pigments are typically a little more difficult mix and breakdown. If this is the case, place the pigments in a small cup, use denatured alcohol and wet the pigments, stir until it has a consistency of a paste. Stir until they break down. Although this video shows neon pigments, the same process can be used for Glow in the Dark pigments. HERE   ADDITIONAL DATA Product Type  Mica Vegan Yes Soaps Yes Epoxy Resin Yes Acrylic Yes FDA-Permitted for External Use Yes FDA-Permitted for Eye Area Use No FDA-Permitted for General (Including Lips) Use No FDA-Permitted for Bath Bombs Use No   NOTE: External use applies to facial make up and nail polish. Bath Bombs fall under the Lips category. We are always asked if our pigments can be used for cosmetic purposes. Below you will find some additional information on FDA Regulations.  FDA:  Fact Sheet: Color Additives and Cosmetics FDA:  Color Additives Permitted for Use In Cosmetics   EPOXY RATIOS Epoxy 2 grams per 8 ounces The most common question that we receive is "How much pigment per gallon of epoxy?". This is a very valid question and unfortunately there is no set answer due to the numerous types of applications and variations. This is why we recommend the 2 grams per 8 oz and add as desired. For example: Are you looking for an opaque or transparent look?  Lighter colors may take more pigment to achieve the color. Why micron sizes matter: PLEASE be aware of the micron sizes of the pigment. The larger the micron, the larger the particle. Typical pigments average 10-60um.  Be aware that larger micron sized pigments will most likely have a heavier density which will cause the pigment to sink faster in fresh epoxy such as deep pours. For example, our Icicle or 14k Nugget Gold is 200-700um and will most likely sink in fresh epoxy faster.  To alleviate sinking either let the epoxy settle up a little bit. Or, come back through your project to "stir" it a little more.   SOAPS RATIOS Soap - Cold process 2 tsp per lb of oils Soap - Hot process ½ tsp lb of MP base   NOTE: Due to the white MP base, it will always create a pastel color.   AUTOMOTIVE / REMOVABLE PAINT RATIOS DO NOT use for these applications. Neon pigments are not UV resistant and will fade over time under constant UV (sun) exposure.  ACRYLIC POURING RATIOS  ALL MEASUREMENTS BY VOLUME Courtesy from our friend Justin Salley. For more tutorial visit his Youtube page HERE. STEP #1- MIX YOUR POURING MEDIUM 3 parts Behr8300 Deep Base Interior/Exterior Hi-Gloss Enamel.  1 part JOSONJA Polyurethane Water Based Gloss Varnish. Mix gently folding paint and varnish together until they are completely mixed, Go Slow to reduce mixing bubbles. STEP #2- DISPERSING PIGMENTS INTO YOUR MEDIUM Pour 1/2 to 1 teaspoon of JOSONJA Gloss Varnish into mixing container.  Add around a teaspoon of Pigment (I generally add a little more) into your container with the JOSONJA.  Mix until all Pigments have dissolved into a liquid making sure to stir any clumps out at this time. STEP #3-  COMBINING YOUR POURING MEDIUM & DISPERSED PIGMENTS Add around 3 Tablespoons of Pouring medium into your Dispersed Pigments.  Mix thoroughly being slow and folding rather than whipping, this will minimize the air bubbles.   STEP #4-  WHAT IF? -If your new mixed color seems to thick- Add a small amount of JOSONJA and stir until you reach the desired consistency. -If your new mixed color seems to thin- Add a small amount of Behr8300 (ONLY) and stir until you reach the desired consistency.   INDUSTRIAL, PLASTICS, & GLASS COATINGS RATIOS Vinyl Wrap And Plastic Films 5-10% By Weight Plastic Bottles 1-2% By Weight Masterbatch 10-30% By Weight Plastic Resins 0.2-0.5% By Weight Rubber Polymers And Latex 5-15% By Weight Glass 1-10% By Weight Candles 5-10% By Weight     GRAPHIC INKS & SCREEN PRINTING RATIOS Flexographic Inks (Packing Materials) 15-25% By Weight Offset Printing Ink 5-10% By Weight Screen Printing And Screen Inks 10-30% By Weight Textile Printing And Textile Inks And Pastes 5-10% By Weight Gravure Inks 5-15% By Weight   COSMETICS RATIOS Nail Polish 5-25% By Weight   FIREARMS (CERAKOTE) RATIOS  Photo Courtesy: crawlinzx14 / Picture shows Eye Candy Colorshift over a black base. Our pigments can be used for both Cerakote and KG Gunkote clears. Below is just some references. 5 grams of pigment per 4oz Typically recommend a black base. For light colored pigments such as yellows, pinks, etc. you may want to try a light colored base. ALWAYS test before full application. 3 coats for full saturation. Some colors may require less. Stay with pigments with a 10-60um micron size. All particle sizes are listed on our product pages or you can find it on our Pigment Information List HERE.  Recommend using a .80 spray nozzle. Some use 1.0 for clears. REQUEST SAFETY DATA SHEET (SDS) To request a safety data sheet, please contact us here:  Jeff@eyecandycustomz.com