CAN-LIN Gateway ECU

Compact ECU with Dual CAN/CAN FD, LIN, and Multi-Purpose I/O The control unit is fully configurable and can be used as a stand-alone data converter between a CAN/CAN FD network and a LIN bus, or as a remote I/O module to interface sensors and actuators to CAN and LIN systems. The control unit supports both SAE J1939 and raw CAN protocols, and is suitable for mobile and stationary applications in harsh automotive and industrial environments. The ECU Configurator (MA-GW-ECU-CONFIG-TOOL) PC application enables simple configuration of the ECU over CAN bus. The user can set ECU’s mode, communication channels’ parameters, inter-channel frame conversion (frame mappings), and I/O mappings. The configuration is stored in the device’s non-volatile memory. Features Tech Specs Documents Downloads Data conversion between CAN, CAN FD and LIN buses One CAN channel One optional CAN FD channel One LIN channel SAE J1939 support Configurable frame and data routing between channels Up to seven multi-purpose inputs and outputs with current measurement Configurable I/O mapping onto CAN or LIN frame data PC tool for easy configuration Waterproof automotive-grade ECU Suitable for 12 V and 24 V systems ECE-R10 (E1) approval (planned for 2021/Q4) Customization on request Usage Examples: CAN-LIN bridge CAN – CAN FD gateway Remote I/O ECU Universal SAE J1939 ECU Property Value The information herein is subject to change without notice. Communication Channels CAN CAN 2.0B (baud rates: 125 / 250 / 500 / 1000 KBaud) Wake-up capable Bus termination: optional (see Ordering Information) LIN LIN v2.2a – ISO 17987 (baud rates: 9600 / 10417 (SAE J2602), 19200 Baud), supports both Master and Slave, and Classic/Enhanced checksums; User-configurable LIN Master’s scheduler CAN FD ISO CAN FD (baud rate up to 8 MBaud): optional Bus termination: optional see Ordering Information CAN Bus Protocols SAE J1939, Raw CAN Inputs and Outputs Number of channels 4 – 7 (see Ordering Information) Channel mode Configurable: Analogue/digital input, HSD output Analogue inputs 0 – 30 V, 12-bit ADC, sample rate 10 ms Digital inputs Configurable voltage threshold HSD with short-circuit protection and current measurement; Digital outputs PWM capable Max. current 1.5 A per channel (2 A in total for IO1-4 and IO5-IO7) Mapping Inputs and outputs can be mapped onto LIN and CAN frame data byte Electrical and Mechanical Input voltage 7 – 30 V DC Power consumption Operation: 0.04 A @ 12 V (+20 °C) Sleep: 40 µA @ 12 V (+20 °C) Power management Options : Automatic wake-up and sleep based on CAN bus activity KL15 (Ignition switch) signal MCU 16-bit Automotive DSP Firmware Firmware update over CAN bus Connector 12-pin Molex MX150 Mating connector: Molex 33472-1201 (p/n: GW-ECU-CONNECTOR-12p) Dimensions (L x W x H) 130 x 75 x 43 mm (5.12” x 2.95” x 1.69” in) Weight 175 g (0.386 lb) Operating temperature -40 to 85 °C (-40 to 185 °F) Ingress Protection IP67 Certifications and Tests Road vehicles ECE-R10 (E1) approval (planned for 2021/Q4) Transient pulses ISO 7637-2 EMC CISPR 25 ESD EN 61000-4-2 Vibrations EN 60068-2-27 EN 60068-2-64 User Configuration ECU modes Communication gateway: Configurable bi-directional frame mapping between CAN and LIN channels, digital and analogue inputs and outputs mappable onto CAN or LIN data frames. SAE J1939: ECU’s inputs and outputs are available over PGNs. Dynamic addressing and DM1 supported. Communication channel parameters CAN and CAN FD: Baud rate, sample point LIN: Baud rate, Checksum type, Master/Slave, scheduling table for LIN Master Configuration User’s configuration is stored in the ECU’s non-volatile memory. PC application ECU Configurator Tool (p/n: GW-ECU-CONFIG-TOOL) is a Windows application that allows to easily configure the ECU over CAN bus. Data Sheet CAN-LIN Gateway ECU Data Sheet in PDF Format