AudioQuest Golden Gate Turntable | RCA Turntable Cable + Ground Wire

Upgrade Your Vinyl Setup With Our AudioQuest Elite Level Golden Gate Cables Premium Solid Perfect-Surface Copper (PSC) conductors Metal-Layer Noise-Dissipation design for RFI prevention Gold-plated, Cold-welded plugs (no solder) for low distortion Foam Polyethylene reduces distortion and yields less "out-of-focus" effect 1.5m (4.9') length From AudioQuest AudioQuest's Golden Gate line is named after the Golden Gate Bridge in San Francisco, once the longest suspension bridge in the world. In AQ's Bridges & Falls series cables, you’ll find better metals and more sophisticated technologies including Air-Tube insulation, Dielectric-Bias System, and the Noise-Dissipation System at reasonable prices. Note: All cables in the Bridges & Falls Series place their left and right channels in a single jacket, and feature an Asymmetrical Double-Balanced geometry with separate high-quality positive and negative conductors. This design allows for a thin, flexible, and uniquely versatile high-performance cable that can be terminated with a variety of today’s connections, including 3.5mm (male or female), DIN, and RCA. Keep in mind, however, that by necessity, the plugs on Bridges & Falls cables are fairly close together. Solid Perfect-Surface Copper (PSC) Conductors Since the beginning, AudioQuest has pioneered the use of superior metals, yet even they were surprised by the huge leap in performance attained through the astonishingly smooth and pure surface of Perfect-Surface Copper (PSC). Proprietary metal-processing technology protects the wire's surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure, and smooth as possible, it becomes a wonderfully low-distortion conductor. In a conventional cable, electrical and magnetic interaction between strands is one of the greatest sources of distortion, often causing a somewhat harsh, dirty sound. Solid conductors are fundamental toward achieving a very clean, natural sound. Metal-Layer Noise-Dissipation System It's easy to accomplish 100% shield coverage. Preventing captured Radio Frequency Interference (RFI) from modulating the equipment's ground reference requires AQ's Noise-Dissipation System (NDS). Traditional shield systems typically absorb and then drain noise/RF energy to component ground, modulating and distorting the critical "reference" ground plane, which in turn causes a distortion of the signal. NDS "shields the shield," absorbing and reflecting most of this noise/RF energy before it reaches the layer attached to ground. Foamed-Polyethylene Insulation Any solid material adjacent to a conductor is actually part of an imperfect circuit. Wire insulation and circuit board materials all absorb energy. Some of this energy is stored and then released as distortion. Because air absorbs next to no energy and Polyethylene is low-loss and has a benign distortion profile, Foamed-PE, with its high air content, causes much less of the out-of-focus effect common to other materials. Direction-Controlled Conductors All drawn metal strands or conductors have a non-symmetrical, and therefore directional, grain structure. AudioQuest controls the resulting RF impedance variation so that noise is drained away from where it will cause distortion. The correct direction is determined by listening to every batch of metal conductors used in every AudioQuest audio cable. When applicable, arrows are clearly marked on the connectors to ensure superior sound quality. For most models of AQ cable, the arrows not only indicate the direction that optimizes metal-directionality as part of Noise-Dissipation, but also indicates non-symmetrical attachment of shield and GND in order to optimize full-system performance. A fundamental aspect of AudioQuest's multifaceted Noise-Dissipation technology, Direction-Controlled Conductors ensure induced noise is dissipated and drained properly. Cold-Welded, Gold-Plated Terminations This plug design allows for a connection devoid of solder, which is a common source of distortion. Instead of solder, the process employs a high-pressure technique. Because the ground shells are stamped instead of machined, the metal used can be chosen for low distortion instead of machinability. Specifications Metal: Solid Perfect-Surface Copper (PSC) Geometry: Asymmetrical Double-Balanced Insulation: Foamed Polyehthylene (PE) Jacket: Red on Black Nylon Braid Weight: 5oz (141.7g) AudioQuest Limited Lifetime Warranty