AudioQuest FireBird High-Current Power Cable

AudioQuest FireBird / High-Current “Paying attention to power cables and power conditioning is not obsessive tweakery for only the most committed audiophiles (you know, the ones who literally hear voices while alone in padded rooms). It is for anyone who pays attention to system choice and setup at any level—a fundamental and utterly essential part of getting good sound.” — GAUTAM RAJA, POSITIVE FEEDBACK, MARCH 2018 Low-Z / Noise-Dissipation 3-Pole AC Power Cable Solid Perfect-Surface Silver (PSS)/Perfect-Surface Copper+ (PSC+) Conductors Uncompressed High-Current Transfer Ground Noise-Dissipation Technology (US Patent # 9,373,439) ZERO: No Characteristic Impedance Dielectric-Bias System with Radio Frequency Noise Trap Directionally Controlled Conductors Alternating Current (AC), is a far-from-perfect power source. AC power technology is well over a century old and was never designed to meet the exacting standards of today’s high resolution audio-video components. AC noise is present at the utility source, and is then exacerbated by radio frequency noise that is induced (picked up by the AC power cord) and coupled to the component power supplies and to circuit ground. This creates distortion and low-level signal losses via the “masking effect.” Further, power amplifiers can require immense reserves of transient current for their power supplies to react to and then stabilize during dynamic audio passages. Most AC power cords and power conditioner-regenerators, though helpful to a point, are simply not up to the task. Power amplifiers present a real challenge for any AC power source, as the transient current requirements (though short in duration) can be many times that of the average (RMS) current consumption. Power amplifiers are also unique from all other components in that the current draw is dynamic, not constant, and it changes with volume and audio signal content. Though many AC power cords may feature low DC resistance to allow for some of this requirement, the characteristic impedance of the AC cable is equally responsible for assuring uncompromised performance. Many premium AC cords constrict or compress the audio transient as their characteristic impedance restricts the transient current. FEATURES GND (GROUND-NOISE DISSIPATION) AC Ground wires provide protection from current-wiring faults, but they also act as antennas. Thus, they are subject to induced radio-frequency (RF) noise. This RF noise bypasses component power supplies and is typically coupled directly into a system’s most sensitive audio/video circuits. AudioQuest’s patented Ground-Noise Dissipation (GND) greatly reduces this distortion, yielding unprecedented levels of noise dissipation across the widest bandwidth (range) of radio frequencies possible. Our unique circuit topology utilizes a common-mode phase-canceling array, in concert with proprietary dielectric materials which provide additional differential linear filtering. (US Patent # 9,373,439) SOLID PERFECT-SURFACE SILVER (PSS) AND SOLID PERFECT-SURFACE COPPER+ (PSC+) CONDUCTORS Solid conductors prevent electrical strand-to-strand interaction, major sources of distortion. Surface quality is critical because a conductor can be considered as a rail-guide for both the fields within a conductor and for the magnetic fields that extend outside the conductor. The astonishingly smooth and pure surface of all AudioQuest’s Perfect-Surface metals nearly eliminates harshness and greatly increases clarity compared to lesser materials. The careful choice of the sizes of the PSS and PSC+ conductors ensures that FireBird’s performance is close to using all PSS Silver but at a much lower cost. UNCOMPRESSED HIGH CURRENT TRANSFER While many AC power cables feature low DC resistance in order to accommodate the demand for high current, a cable’s characteristic impedance is also crucial for optimal performance. Unlike most AC cables that constrict or compress an audio-provoked transient, AudioQuest AC cables combine low DC resistance and ZERO (no) characteristic impedance in order to deliver uncompressed high-current transients on demand. DIELECTRIC-BIAS SYSTEM WITH RADIO FREQUENCY TRAP All insulation between two or more conductors is also a dielectric whose properties will affect the integrity of the signal. When the dielectric is unbiased, dielectric-involvement (absorption and non-linear release of energy) causes different amounts of time delay (phase shift) for different frequencies and energy levels, which is a real problem for very time-sensitive multi-octave audio. The inclusion of an RF Trap (developed for AudioQuest’s Niagara Series of power products), ensures that radio-frequency noise will not be induced into the signal conductors from the DBS field elements. (DBS, US Pat #s 7,126,055 & 7,872,195 B1) DIRECTIONALITY All drawn metal strands or conductors have a non-symmetrical, and therefore directional, grain structure. AudioQuest controls the resulting RF impedance variation so that noise is drained away from where it will cause distortion. The correct direction is determined by listening to every batch of metal conductors used in every AudioQuest audio cable. When applicable, arrows are clearly marked on the connectors to ensure superior sound quality. For most models of AQ cable, the arrows not only indicate the direction that optimizes metal-directionality as part of Noise-Dissipation but also indicates non-symmetrical attachment of shield and GND in order to optimize full-system performance. HELP!!! Do I need 15 amp or 20 amp? Some gear might say they are 20 amp, but still use the 15-amp IEC connector. To determine which one you need for your application, take a look at this drawing of the two types of IEC connectors. Pick the one that matches the IEC socket on your gear.