8th-9th Gen F150 Rear Disc Brake Conversion kit (17in)

Finally a disc brake conversion that doesn't break the bank and replaces the century old drum brake design. this Kit is for 8th-9th gen f150s with the 8.8 rear end running 17 inch wheels.   Product Information: Country of origin: USA color: Flat black powdercoat material: HRS, 6061 AL mounting type: bolt on included components: (2) brackets (2) rotors (2) calipers with pads (6) spacers (6) grade 8 bracket bolts with included nuts and washers (4) stainless steel caliper bolts (2) park brake sleeves with included snap rings (2) cable end adapters with included roll pins. (2) braided brake lines (1) wilwood adjustable proportioning valve (2) brake line tube nuts WARNING!!! THIS KIT IS INTENDED FOR OFFROAD USE ONLY NOT FOR HIGHWAY USE! This kit is designed to utilize 2004-2006 E150 rotors (5 lug) with 2005-2010 mustang rear calipers. supplied below are some part numbers for reference that was used on the test truck and are still in operation today. Part Number Reference  18B4927 & 18B4926 (bracketed s197 mustang brake calipers) 950.61501 (stop tech braided brake lines) BLF-31B (bubble flare to inverted flare adapter) PRT5697 (stock 2004 E150 rotors) 633-54192L & 633-54192R (drilled and slotted rotors) 260-8419 (wilwood proportioning valve) 260-13783 (wilwood 2lb residual valve) Install notes: stock s197 brake hoses will not work! it puts the hose in a bind any way you try to route it, also runs into leaf spring clearance. to run the stop tech braided lines, you will need to use the bubble flare to inverted flare adapter or it will leak.  you may need to replace your 10lb residual valve with a 2lb one which is meant for rear disc brakes. not doing so may cause the brakes to drag. an adjustable proportioning valve will get your brake bias dialed in once installed. make sure when you install the calipers that the bleeder screw is facing up and not down. it will not bleed correctly causing brakes to be soft or fail completely. you may have to flip the caliper sides (driver side to passenger side and vise versa) to get the bleeder screw facing straight up. brackets were designed to point towards the rear of the truck. Note: all orders are MTO (made to order), expect a 3-4 week lead time! DISCLAIMER The person that is purchasing this product makes the following representations and acknowledges and agrees to the following terms and conditions: This product is for off-road use only and is designed and intended for use in organized, amateur and professional off-road events, but is limited to closed-course events and open-course events that is formally sanctioned by a recognized event organization involving the motor vehicle in which it is installed (the “vehicle”). It is not for use on public highways or roads. The person or entity buying this product and/or using this product (the “user”) agrees to use the vehicle solely for off-road uses as described herein, and the user acknowledges that the purchase, installation, and use of this product all comply with federal, state, and local laws, regulations and ordinances by the user. The user accepting this disclaimer acknowledges and hereby indemnifies and saves harmless Jimmy Broom, and JFAB Machining from any damages, penalties, fines, expenses or other costs which may arise from the use of this product and without limiting the generality of the foregoing specifically acknowledges the following: ·        Use of this product for purposes other than solely off-road events may be a violation of federal, state law or local environmental, motor vehicle and other laws. The user warrants that this product shall only be used in sanctioned off-road events. ·        That use of this product may violate warranties from the manufacturer of the vehicle or from others. ·        That use of this product may make the vehicle unfit or unsafe for the purposes intended or for any purpose and cause personal injury, property damage or death. ·        That the installation of this product, improper installation of this product, use of this product with other components, could result in or cause personal injury, property damage, or death. USE THIS PRODUCT AT YOUR OWN RISK. THE RESPONSIBILITY FOR THE USE OF THIS PRODUCT AND INSTRUCTION SHEET LIES WITH THE USER. By using the instruction sheet and product, you agree that this instruction sheet and product is provided “AS IS” and Jimmy Broom or JFAB Machining does not make any specific representations or warranties about this instruction sheet or product. Jimmy Broom or JFAB Machining does not make any warranties about the contents of the instruction sheet, the product, or its accuracy, reliability, or ability to meet your needs. The knowledge and experience level of the users of this product and instruction sheet vary widely; if you do not have adequate knowledge and experience to use this product and instruction sheet safely to accomplish the tasks described, please hire a professional to assist you for your safety and the safety of your vehicle and others. Limitation of liability ·        Jimmy Broom or JFAB Machining is not liable for any errors, mistakes, or inaccuracies in the instruction sheet and product.   ·        This limitation of liability provision applies to any claim regardless of whether the claim asserted is based on warranty,contract, tort or any other legal theory. Use the instruction sheet and product at your own risk. Any injury, damage, or loss that may result from use of the tools, equipment, products, or information contained in this instruction sheet or product is the sole responsibility of the user. INDEMNITY To the extent permitted by applicable law, you agree to defend, indemnify and hold harmless Jimmy Broom and JFAB Machining from and against any and all claims, damages, obligations, losses, liabilities, costs or debt, and expenses (including but not limited to attorneys fees) Arising from: (i) your use of and access to this instruction sheet and product; (ii) your violation of any term of the agreement; (iii) your violation of any third party right, including without limitation any copyright, property, or privacy right; or (iv) any claim that your actions caused damage to Jimmy Broom, JFAB Machining or a third party. The defense and indemnification obligations will survive this agreement and your use of this instruction