84" CANbus Cable for GC2 Golf Cart Modules

Epoch 84" CANbus Cable for GC2 Golf Cart Modules The official 84-inch CANbus cable for long-run Epoch GC2 lithium golf cart battery communication. This Epoch GC2 communication cable is built for custom golf cart installs, split battery compartments, extended module-to-module runs, and dash-gauge routing. Use this 84" CANbus cable to help compatible Epoch GC2 golf cart battery modules share BMS data, synchronize communication, and maintain accurate telemetry across your lithium battery system. Built for long-run GC2 communication Official Epoch part: Made for GC2 modules 84-inch reach: 7-foot routing flexibility Split compartments: Bridge custom layouts Dash gauge routing: Send battery data forward BMS data sync: Supports module communication No splicing: Plug-and-play installation Essential for Custom Installs & Split Compartments Give your Epoch GC2 communication cable the length needed for non-standard golf cart battery layouts. Custom golf cart lithium installs often place GC2 golf cart battery modules farther apart than a standard side-by-side tray. This 84-inch data cable gives builders and technicians the reach needed to bridge split battery compartments, route around seat bases, or span longer paths while keeping each module connected to the battery communication network. Use this Epoch CANbus wire when your build requires a clean 7-foot battery communication run instead of a short module bridge cable. It is a communication accessory only; always keep correctly sized power cables, fuses, and disconnects in place for current-carrying connections. Route Battery Data Directly to Your Dash A practical long cable option for golf cart dash gauge and monitoring runs. The 84-inch length is ideal for routing from an Epoch GC2 module under the seat or in a battery bay toward a dashboard display location. That makes it easier to keep accurate state-of-charge and system telemetry visible where the driver can monitor the golf cart lithium battery system during daily use. Genuine OEM Quality: Plug-and-Play & Protected Routing Avoid communication errors caused by unverified wiring and loose routing. Genuine Epoch parts help keep connector fitment, pinout compatibility, and BMS communication aligned with your GC2 battery system. The pre-terminated plug-and-play design eliminates cutting and splicing, while proper routing helps protect the cable from vibration, pinching, moisture exposure, and battery bay wear. 84-Inch Extended Reach A 7-foot cable gives installers extra distance for custom golf cart battery trays, split compartments, and longer dash-gauge routing paths. GC2 Battery BMS Communication Supports communication between compatible Epoch GC2 modules so the system can share data, synchronize operation, and provide more accurate battery telemetry. Plug-and-Play Installation Pre-terminated connectors help make installation simple—no cutting, crimping, or splicing required for compatible GC2 CANbus ports. Cleaner Custom Builds Use the extended cable to reduce awkward routing, avoid stretched cables, and keep GC2 lithium battery communication wiring organized. Replacement or Extension Cable A useful accessory when the original cable is damaged, missing, or not long enough for a modified golf cart lithium installation. Communication Only This cable carries data, not drive current. It does not replace power cables, battery interconnects, fuses, shunts, or disconnect switches. Installation overview Power down, connect, route, secure, and verify communication. 1. Power off modules: Turn off the GC2 modules before beginning the installation. 2. Identify CAN ports: Locate the designated communication ports on the compatible Epoch GC2 modules. 3. Connect the cable: Plug the cable into the proper CANbus ports according to your GC2 wiring diagram. 4. Route safely: Avoid sharp edges, heat sources, pinch points, moving parts, and excess tension. 5. Verify data: Power the system on and confirm communication through the BMS, gauge, or compatible monitor. Communication cable notice This accessory is for CANbus communication between compatible Epoch GC2 battery modules and monitoring components. It does not carry battery current and should never be used as a substitute for properly sized power wiring. Ideal uses For custom Epoch GC2 lithium golf cart battery installations. ✓Connecting Epoch GC2 batteries in parallel configurations that require communication linking. ✓Bridging split battery compartments in custom golf cart lithium conversions. ✓Routing GC2 battery communication from the battery bay toward a dash gauge or display. ✓Replacement or spare communication cable for compatible Epoch GC2 module systems. ✓Golf cart lithium battery telemetry, BMS data sharing, and coordinated multi-module operation. Technical specifications Exact product details for the 84-inch GC2 CANbus cable. Product details Product name  84 inch CANBus Cable for GC2 Golf Cart Modules SKU 84inch-canbus-cable Brand Epoch Batteries Product type GC2 golf cart battery CANbus communication cable Cable length 84 inches / 7 feet Compatibility Epoch GC2 lithium golf cart battery modules Communication type CANbus data communication Primary use Long-run BMS communication, module synchronization, dash-gauge routing, and telemetry support Installation style Plug-and-play cable connection between compatible communication ports Ideal layouts Split battery compartments, extended module-to-module runs, custom golf cart builds, and replacement communication cable routing Power cable replacement No — this is a data cable only and does not replace battery power cables, fuses, or disconnects What is included 1 × Epoch 84 inch CANbus communication cable Care guidance Inspect regularly, avoid pinch points and sharp edges, keep connectors fully seated, and protect the cable from excess tension or heat Maintenance and care Protect the cable for stable CANbus communication. Inspect the cable and connectors periodically for wear, damage, corrosion, or loose connections. Route the 84-inch cable so it is not stretched, pinched, crushed, exposed to sharp edges, or placed against high-heat surfaces. Keep connectors fully seated and clean them with a soft cloth if dirt or corrosion appears.