Electro-Harmonix 720LOOPER 720 Stereo Looper

With 720 seconds (12 minutes) of stereo recording time on 10 independent loops and unlimited overdubbing, the compact 720 Stereo Looper provides guitarists with an intuitive tool that’s perfect for practice and live performance. Controls LEVEL Knob – Controls the output level of the Loop being played. Your dry signal remains at unity signal level from input to output.  LOOP Footswitch – Use the LOOP footswitch to record, overdub, and playback loops. The LOOP footswitch can also be used to stop and undo-redo loops.  STOP/FX Footswitch – The STOP/FX footswitch can be set to either STOP mode or FX mode. Select either mode by pressing and holding the PUSH: MODE button for 2-seconds.  REC LED – Indicates when a loop is being recorded or overdubbed. PLAY LED – Indicates when a loop is being played or overdubbed. MEM LED – Indicates loop audio is in memory for the current loop bank. LOOP Knob and PUSH: MODE Button – The LOOP knob has no pointer because it is attached to a rotary encoder that can be continuously rotated in either direction.  SELECTING/ ADJUSTING MODES – The 3 selectable modes are toggled on and off by pressing the MODE button once.  L = Loop Select p = Loop Progress F = Fadeout Time When you arrive at the mode you would like to adjust, press the MODE button once to select the mode. The display will stop flashing and it will show the selected mode value from 0-9.  REVERSE Button – Press the REVERSE button to play the loop in reverse. The REVERSE button glows red when enabled. Reverse can be used at any time to playback or overdub a loop. ½ SPEED Button – Pressing the ½ SPEED button causes the pitch of the loop to go down one octave and the tempo is halved. If a loop is overdubbed during half-speed mode, returning to normal speed playback causes the pitch of the overdub to go up one octave and the tempo is doubled.  FX LED – Indicates when an effect is active. The FX LED automatically lights when the REVERSE or ½ SPEED buttons are used and the STOP/FX footswitch is programmed to operate in STOP mode. MONO/L INPUT – ¼” Left Instrument/Line Input Jack. Plug the output of your instrument or another effects pedal into this jack. If you use just one input we recommend you use the MONO/L input. The input impedance presented at this jack is 1MΩ. R INPUT – ¼” Right Input Jack. Plug the output of your instrument or another effects pedal into this jack. Use this jack for stereo recording. The input impedance presented at this jack is 1MΩ. MONO/L OUTPUT – ¼” Left Output Jack. The Left output signal is sent through this jack. The dry signal present at the Left input will be output on the MONO/L Output jack. Note: the MONO/L OUTPUT jack also functions as a power switch when powered from a battery. R Output – ¼” Right Output Jack. The Right output signal is sent through this jack. The dry signal present at the Right input jack is output to the R Output jack. FC Jack – ¼” TRS Foot Controller Jack. Use this jack with popular three button foot controller units to control the 720 bank up, bank down, and instant undo-redo. The Digitech® FS3X 3-Button Footswitch [see: http://digitech.com/en-US/products/fs3x-3-button-footswitch] is recommended for this application.  The circuit required for the foot controller is as follows: TIP / S1 = Instant Undo-Redo RING / S2 = Bank Down Diode-AND TIP+RING / S3 = Bank Up 9V Power Jack – Plug the output of the supplied AC adapter into the 9V power jack located at the top of the 720. The Stereo Looper 720 draws 60mA typ./75mA max. at 9VDC with a center-negative plug. The Stereo Looper 720 accepts Boss® and Ibanez® style AC adapters. Specs Extra-long 12 minutes of stereo recording time 10 independent loops Undo-Redo, Reverse and ½ Speed Effects at the touch of a button High-quality, uncompressed audio, 24-bit A/D/A converters plus 44.1kHz sample rate Stereo in/out for enhanced usability… record two instruments at once Foot controller input provides a way to use popular 3-button foot controllers to change a bank up or down, and gives access to instant Undo-Redo Silent footswitches Loop fadeout (trails) mode EHX 9.6VDC-200mA power supply included Works on 9V battery and provides extended battery life Current Draw: 75mA @ 9VDC Dimensions in inches: 4.0(w) x 4.75(l) x 2.25(h) Dimensions in mm: 102(w) x 121(l) x 58(h)