3 Silicone Blades - Replacement set for the ULTIM8™ WYP

Description Contents & Tech Install & Use This replacement blade set comes with three high-grade silicone blades, each suited for different tasks: Perforated Blade: Features vertical slots to mix resin that has been sitting in the vat for extended periods to avoid print defects. Long Blade: Ideal for general cleanup and wiping down the vat safely without causing damage to the FEP and vat. Short Blade: Perfect for tight spaces and designed to work with our 3D-printable basket to filter resin for debris that can cause print defects. All ULTIM8™ WYP blades are resistant to resin and IPA, making clean-up simple. You can soak the tool in IPA after use, then dry and wipe it down when ready for the next project. What's Included: It comes with 3 high-grade silicone blades for various uses. The mixing Blade is a large blade with vertical slots to assist in mixing resin that has been sitting in the vat for extended periods. The Long Blade is used for all general clean up and spatula work while wiping down the resin vat. The Short Blade is used anywhere space may be a concern and to be used with our 3D-printable basket to filter your resin in the vat. Specifications: Long Blade: Material: Injection molded first-grade silicone Dimensions: 25 x 76 x 7 mm Mixing Blade: Material: Injection molded first-grade silicone Dimensions: 25 x 76 x 7 mm Short Blade: Material: Injection molded first-grade silicone Dimensions: 15 x 76 x 7 mm Click here for the downloadable instructions. Attention: when working with resin always use the appropriate eye protection and gloves to avoid contact with the resin. To use insert one of our included blades: +Mixing Blade to Mix If your resin has been sitting in the vat for more than 12 hours, it is critical to mix it thoroughly before initiating the printing process. Over time, resin components tend to separate based on their densities, which can lead to print defects or complete failures. Follow these steps for the best results mixing: Position the build plate: raise the build plate to its uppermost position on the Z-axis. Mixing with the ULTIM8™ WYP Blade: using the ULTIM8™ WYP (not included) equipped with a silicone Mixing Blade, methodically wipe the resin in the vat. Perform slow, deliberate strokes, applying enough downward pressure to ensure the blade contacts the FEP film at the vat’s bottom. This will help mix any resin that has settled and ensure uniformity throughout the entire volume. Avoid Over-Spill: mix at a controlled speed to prevent creating waves that may cause the resin to overflow from the vat. Resin Quality Check: while mixing, observe for any solidified resin pieces. If detection occurs, it's advisable to halt operations and clean both the FEP and VAT. Alternatively, transfer the resin into an external container using a fine filter and funnel, such as our ULTIM8™ FUN, to eliminate any contaminants. Proper resin mixing is essential for maintaining print quality and preventing issues related to separation or contamination. +Long Blade to Wipe Follow these steps for the best results when cleaning: Remove resin vat. Initial Wipe: start by using the long silicone blade to remove excess resin from the vat. The flexible design allows you to cover larger areas quickly while preventing scratches on sensitive surfaces. Edge Cleanup: use the blade to wipe around the edges and corners of the vat, ensuring all resin is cleared without damaging the FEP film. Surface Wipe: gently wipe down the FEP film, applying minimal pressure. The silicone material ensures a smooth and safe cleaning process, avoiding damage to the film. Final Pass: perform a final wipe to ensure no residue is left behind, leaving your vat ready for the next use. The Long Blade's durable silicone construction is designed for frequent use, providing consistent results for general cleanup and spatula work. +Short Blade to Filter The Short Blade is an ideal solution for filtration tasks in confined spaces. For enhanced functionality, pair it with our free 3D-printable basket to efficiently filter resin directly within the vat. Follow these steps for the best results: Install the 3D-printed basket inside the Tool (optional) Position the ULTIM8™ WYP tool, equipped with the Short Blade, near the vat’s edge. Gently drag the silicone blade along the FEP film, keeping the WYP angled so that resin flows over the blade and into the basket. Periodically inspect the basket to ensure debris is collected. Clean Up: Clean up is easy as all parts are very resistant to resin components and IPA, so it is possible to leave all sitting in IPA to clean after use until ready to dry off and wipe down.